In my vio server I have the below output
In my vio client lpar I have the below output
So it is clear that the cd device has been served to the lpar by the vio server. My question is why there are 2 cd devices showing up in available state?
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
LEARN ABOUT FREEBSD
hv_netvsc
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)NAME
hv_netvsc -- Hyper-V Network Virtual Service Consumer
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_netvsc driver implements the virtual network device for FreeBSD guest partitions running on Hyper-V. FreeBSD guest partitions running
on Hyper-V do not have direct access to network devices attached to the Hyper-V server. Although a FreeBSD guest can access network devices
using Hyper-V's full emulation mode, the performance in this mode tends to be unsatisfactory.
To counter the above issues, the hv_netvsc driver implements a network Virtual Service Consumer (VSC) that relays network requests from the
guest partition to the network Virtual Service Provider (VSP) hosted in the root partition using the high performance data exchange infra-
structure provided by hv_vmbus(4) driver. The VSP in the root partition then forwards the network related requests to the physical network
card.
SEE ALSO hv_ata_pci_disengage(4), hv_storvsc(4), hv_utils(4), hv_vmbus(4)HISTORY
Support for hv_netvsc first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation, and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_netvsc was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD September 10, 2013 BSD