In my vio server I have the below output
In my vio client lpar I have the below output
So it is clear that the cd device has been served to the lpar by the vio server. My question is why there are 2 cd devices showing up in available state?
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
LEARN ABOUT DEBIAN
readdvd
readdvd(1) readdvd 1.0 readdvd(1)NAME
readdvd - is creating an image of your source dvd media or medias even if it has / they have corrupted blocks
SYNOPSIS
readdvd [-l] [-h]
readdvd -d DEVICE1 [-d DEVICE2] [-d ...] -o file.iso [-s #] [-v] [-vv]
DESCRIPTION
readdvd reads even a corrupted dvd and writes the the result into a new image file on your harddisk.
DEVICE
can be an IDE, SCSI, SATA, USB or FireWire connected optical drive. Not all SATA controller support all Plextor features.
Linux:
/dev/hdX: IDE device
/dev/scdX: Linux 2.4: SATA, SCSI, USB device, or IDE device via ide-scsi emulation
/dev/srX: Linux 2.6: IDE device via new ATA layer, SCSI or USB device
OpenBSD/NetBSD:
/dev/rcdX
FreeBSD:
/dev/cd: SCSI device
/dev/acd: ATA device
MacOS X:
/dev/disk:
win32:
C:,D:,E:, ... X:,Y:,Z:
OPTIONS -l scan busses for all available CD and DVD devices
-h help shows available options.
-o file.iso
write data to imagefile named file.iso
-s # read source media with selected speed
-v use verbose mode
-vv use extended verbose mode
INTERACTIVE MODUS
q stop reading media and exit
w save sector map which is currently read and continue with the next one
EXAMPLES
readdvd -d /dev/sr0 -o filename.iso -s 8 -v
create an image filename.bin of inserted media in device /dev/sr0 with read speed 8 in verbose mode.
please report man page improvements to T.Maguin@web.de
Gennady ShultZ Kozlov 10. April, 2009 readdvd(1)