06-01-2012
I think going back to 90's interfaces would quickly get old.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there,
I am installing a package at the moment on to my Solaris version 8 and I have run into a problem with the 'make' command. I have installed the package using the 'pkgadd' command and I am now at the stage where I have to use the 'make' command followed by the 'make install'... (4 Replies)
Discussion started by: gerwhelan
4 Replies
2. What is on Your Mind?
We were at Champs watching the Belmont on two 15' screens.
SMARTY JONE!! SMARTY JONES!!!
Then, sadness........ the crowd goes quiet. There are many people who have not seen a triple crown winner in their lifetime......
Amazing... Horse racing! (8 Replies)
Discussion started by: Neo
8 Replies
3. Linux
Hi,
Recently I install a package and try to do a make and make install.
However, in the make it gives me below error:-
make:Nothing to be done for 'install-exec-am'
make:Nothing to be done for 'install-data-am'
Can anyone please explain to me what does this mean? I have been trying... (1 Reply)
Discussion started by: ahjiefreak
1 Replies
4. Solaris
I attached a README file that I will refer to.
I successfully completed everything in the README file until step 4.
# pwd
/gani/gani-2.4.4
# ls
COPYING Makefile.macros gem.c
Makefile Makefile.sparc_gcc gem.h
Makefile.amd64_gcc ... (1 Reply)
Discussion started by: Bradj47
1 Replies
5. Programming
How I can get the current make-file name in a make-file
So, if I run make with specified file:make -f target.mak
is it possible to have the 'target' inside of the that 'target.mak' from the file name? (2 Replies)
Discussion started by: alex_5161
2 Replies
6. UNIX for Dummies Questions & Answers
Hi, Sorry for my English.
I want Execute a make from other folder but no it's a normal make.
The comand is:
make telosb install,3
And for example if i have to execute this comand in /tmp and i am in /$HOME
how he would be now the comand?
thx (7 Replies)
Discussion started by: Grobix
7 Replies
7. UNIX for Dummies Questions & Answers
Hi,
While installation of apache on linux, we perform the below tasks.
1) Untar
2) configure
3) make
4) make install.
I wanted to understand the difference and working of configure/make/make install.
Can any one help me understanding this?
Thanks in advance. (1 Reply)
Discussion started by: praveen_b744
1 Replies
8. Programming
I have been trying to split up my src directory to clear out files that are not re-compiled very often. Now I have the following setup in my trunk,
trunk/bld
trunk/src/
trunk/src/src_server
trunk/makefile.linux
In the make file, I have compile rules
SOURCELOC = src
# compile src c++... (4 Replies)
Discussion started by: LMHmedchem
4 Replies
9. AIX
AIX 7.2 - needs POWER7 or later
With AIX 6.1 it was POWER4 or later - then I was "Happy Me!" because I already had a POWER4 system.
With AIX 7.2 - for now I am "sad me" because I do not have a POWER7. However, next week I am going to be speaking at the POWER TechU in Cannes (look me up if you... (8 Replies)
Discussion started by: MichaelFelt
8 Replies
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces.
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD