05-24-2012
In the area of unwanted advice... you may want to consider upgrading to either 6.0.0,
https://www.unix.com/302122411-post1.html
or 5.0.7V, although the virtual version is sold as an annual subscription, not a one time purchase. I have also heard that there is going to be a 6.0.0V.
10 More Discussions You Might Find Interesting
1. SCO
I've installed a CD-RW rom using SCO OSR 5.0.7, but I cannot open the dev to perform backup (6 Replies)
Discussion started by: tsc_hk
6 Replies
2. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
3. Solaris
Hi,
I attached the CDROM device in sun 2500 system , Now i want to mount this device.
From where i can find the CDROM device.
Thnx.. (2 Replies)
Discussion started by: Aamir Sahil
2 Replies
4. SCO
Looking for specifically naming convention for a tape device for SCO Unix
What full system backup command should I use for SCO UNIX (1 Reply)
Discussion started by: jedimaster
1 Replies
5. Solaris
Hi,
I've seen similar posts on this board about ejecting CDROMs but I've tried the solutions people suggested but still cannot eject the CD. It's stuck in a production box so I can't reboot it...
bash-3.00# eject -f cdrom
/vol/dev/dsk/c0t0d0/sol_10_106_sparc/s0: Device busy
bash-3.00#... (14 Replies)
Discussion started by: jimmy54321
14 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. SCO
This is my first load of SCO OpenServer v5.0.7 on a HP ProLiant ML350 G6. When it asks me to identify the source media it can't find it no matter how I respond. The SCO compatible page says it used the on board SATA DVD-ROM on Port 2 of the embedded SATA controller with "Legacy IDE emulation (as... (8 Replies)
Discussion started by: farmboy
8 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. HP-UX
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
Discussion started by: bstring
5 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
LEARN ABOUT DEBIAN
io::all::http
IO::All::HTTP(3pm) User Contributed Perl Documentation IO::All::HTTP(3pm)
NAME
IO::All::LWP - Extends IO::All to HTTP URLs
SYNOPSIS
use IO::All;
$content < io('http://example.org'); # GET webpage into scalar
io('http://example.org') > io('index.html'); # GET to file
"hello
" > io('http://example.org/index.html'); # PUT webpage
# two ways of getting a page with a password:
$content < io('http://me:secret@example.org');
$content < io('http://example.org')->user('me')->password('secret');
DESCRIPTION
This module extends IO::All for dealing with HTTP URLs. Note that you don't need to use it explicitly, as it is autoloaded by IO::All
whenever it sees something that looks like an HTTP URL.
The SYNOPSIS shows some simple typical examples, but there are many other interesting combinations with other IO::All features! For
example, you can get an HTTP URL and write the content to a socket, or to an FTP URL, of to a DBM file.
METHODS
This is a subclass of IO::All::LWP. The only new method is "http", which can be used to create a blank IO::All::HTTP object; or it can also
take an HTTP URL as a parameter. Note that in most cases it is simpler just to call io('http://example.com'), which calls the "http" method
automatically.
OPERATOR OVERLOADING
The same operators from IO::All may be used. < GETs an HTTP URL; > PUTs to an HTTP URL.
SEE ALSO
IO::All, IO::All::LWP, LWP.
AUTHORS
Ivan Tubert-Brohman <itub@cpan.org> and Brian Ingerson <ingy@cpan.org>
COPYRIGHT
Copyright (c) 2007. Ivan Tubert-Brohman and Brian Ingerson. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
See <http://www.perl.com/perl/misc/Artistic.html>
perl v5.10.0 2007-03-29 IO::All::HTTP(3pm)