05-24-2012
USB floppies should all be the same 'kind', so to speak, AFAIK.
This User Gave Thanks to Corona688 For This Post:
10 More Discussions You Might Find Interesting
1. SCO
I've installed a CD-RW rom using SCO OSR 5.0.7, but I cannot open the dev to perform backup (6 Replies)
Discussion started by: tsc_hk
6 Replies
2. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
3. Solaris
Hi,
I attached the CDROM device in sun 2500 system , Now i want to mount this device.
From where i can find the CDROM device.
Thnx.. (2 Replies)
Discussion started by: Aamir Sahil
2 Replies
4. SCO
Looking for specifically naming convention for a tape device for SCO Unix
What full system backup command should I use for SCO UNIX (1 Reply)
Discussion started by: jedimaster
1 Replies
5. Solaris
Hi,
I've seen similar posts on this board about ejecting CDROMs but I've tried the solutions people suggested but still cannot eject the CD. It's stuck in a production box so I can't reboot it...
bash-3.00# eject -f cdrom
/vol/dev/dsk/c0t0d0/sol_10_106_sparc/s0: Device busy
bash-3.00#... (14 Replies)
Discussion started by: jimmy54321
14 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. SCO
This is my first load of SCO OpenServer v5.0.7 on a HP ProLiant ML350 G6. When it asks me to identify the source media it can't find it no matter how I respond. The SCO compatible page says it used the on board SATA DVD-ROM on Port 2 of the embedded SATA controller with "Legacy IDE emulation (as... (8 Replies)
Discussion started by: farmboy
8 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. HP-UX
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
Discussion started by: bstring
5 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
UPLCOM(4) BSD Kernel Interfaces Manual UPLCOM(4)
NAME
uplcom -- USB support for Prolific PL-2303/2303X/2303HX serial adapters driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uplcom
device ucom
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
uplcom_load="YES"
DESCRIPTION
The uplcom driver provides support for various serial adapters based on the Prolific PL-2303, PL-2303X and PL-2303HX USB-to-RS232 Bridge
chips.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
HARDWARE
The uplcom driver supports the following adapters:
o ATEN UC-232A
o BAFO BF-800
o BAFO BF-810
o Belkin F5U257
o ELECOM UC-SGT
o HAL Corporation Crossam2+USB IR commander
o Hama USB RS-232 Serial Adapter
o Hamlet exagerate XURS232
o IOGEAR UC-232A
o I/O DATA USB-RSAQ
o I/O DATA USB-RSAQ2
o I/O DATA USB-RSAQ3
o Mobile Action MA-620 Infrared Adapter
o PLANEX USB-RS232 URS-03
o RATOC REX-USB60
o Radio Shack USB Serial Cable
o Sandberg USB to Serial Link (model number 133-08)
o SOURCENEXT KeikaiDenwa 8 (with and without charger)
o Sony Ericsson USB Cable (Susteen USB Data Cable)
o Willcom W-SIM DD PHS terminal.(WS002IN)
SEE ALSO
tty(4), ucom(4), usb(4)
HISTORY
The uplcom driver appeared in NetBSD 1.6. This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org> in April 2002.
BSD
November 22, 2006 BSD