05-24-2012
USB floppies should all be the same 'kind', so to speak, AFAIK.
This User Gave Thanks to Corona688 For This Post:
10 More Discussions You Might Find Interesting
1. SCO
I've installed a CD-RW rom using SCO OSR 5.0.7, but I cannot open the dev to perform backup (6 Replies)
Discussion started by: tsc_hk
6 Replies
2. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
3. Solaris
Hi,
I attached the CDROM device in sun 2500 system , Now i want to mount this device.
From where i can find the CDROM device.
Thnx.. (2 Replies)
Discussion started by: Aamir Sahil
2 Replies
4. SCO
Looking for specifically naming convention for a tape device for SCO Unix
What full system backup command should I use for SCO UNIX (1 Reply)
Discussion started by: jedimaster
1 Replies
5. Solaris
Hi,
I've seen similar posts on this board about ejecting CDROMs but I've tried the solutions people suggested but still cannot eject the CD. It's stuck in a production box so I can't reboot it...
bash-3.00# eject -f cdrom
/vol/dev/dsk/c0t0d0/sol_10_106_sparc/s0: Device busy
bash-3.00#... (14 Replies)
Discussion started by: jimmy54321
14 Replies
6. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
7. SCO
This is my first load of SCO OpenServer v5.0.7 on a HP ProLiant ML350 G6. When it asks me to identify the source media it can't find it no matter how I respond. The SCO compatible page says it used the on board SATA DVD-ROM on Port 2 of the embedded SATA controller with "Legacy IDE emulation (as... (8 Replies)
Discussion started by: farmboy
8 Replies
8. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
9. HP-UX
Hello,
I am following the HPUX 11.31 install/update guide and I am trying to install "Update-UX" from the installation media. I put the CD into the drive, and I am trying to mount the device. The instructions state:Find the DVD-ROM device file name:
ioscan -C disk -f -n -k | more
A typical... (5 Replies)
Discussion started by: bstring
5 Replies
10. SCO
Hi all,
A client has an SCO OpenServer Server 6.0, that is running on an HP ProLiant Box and they lost the root password.
Its equipped with a Doal-Core Intel Pentium Processor. They don't have any media or emergency disk anymore.
I tried to boot with the CD Rom, then "Tools", then exit to... (7 Replies)
Discussion started by: thm2222
7 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD