Type
to see what disks are in vg00
then again
And look at the last stanza : You should see something like:
Hoping it will tell you what disk is failing... or already dead e.g:
Also, look what you have in your /var/adm/syslog/syslog.log ! You may fins EM- critical messages...
I dont even know what raid level this is, but its raid 5 mirrored from the looks of it.
I have a failed disk (t12) within this mirror. What is the best way to replace this disk? 2 things concern me, isn't there a command to prepare the disk for a hot swap? and what should i do with the... (3 Replies)
Hi Experts,
I have configured A D40 Array. There is an faulty disk which is not part of an raid volume but shows fault in the diagnostics.
pdisk15 U0.1-P1-I1/Q1-W40AA83CC2400D
SSA160 Physical Disk Drive ( MB)
Is there a way to stop this... (2 Replies)
Hi,
Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great.
# uname –a
SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4
#df -k
Filesystem kbytes used... (3 Replies)
Requirement to remove a faulty mirrored disk from hp-ux LVM
<root@pdwp1s>/etc # vgdisplay -v /dev/vg00
vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0":
The specified path does not correspond to physical volume attached to
this volume group
vgdisplay: Warning: couldn't... (9 Replies)
Hi,
Have mirrored the primary disk to 3 .
Server and OS:
# uname -a
HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license
# model
9000/800/L3000-7x
# strings /etc/lvmtab
/dev/vg00
+F@<
/dev/dsk/c1t2d0
/dev/dsk/c2t2d0
/dev/dsk/c2t0d0
But now I have only 1 disk... (5 Replies)
Hi Guys,
One of two disks in my solaris machine has failed, the name is disk0, this is SUN physical sparc machine
But I work remotely, so people working near that physical server are not that technical, so from OS command prompt can run some command to bink faulty disk at front panel of Server.... (9 Replies)
Hi,
One of my disk is in 'disk missing state'. It is a sharedVG and cluster nodes.
The errpt keeps reporting stale partition error.
lvs are in open/stale state.
In this sceanario is replacing the disk the best practice?
When i do a lsdev the disk is labelled as below.
hdisk3 Available ... (2 Replies)
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply)
-> show faulty
Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
LEARN ABOUT HPUX
standards
standards(5) File Formats Manual standards(5)NAME
standards - UNIX standards behavior on HP-UX
DESCRIPTION
HP-UX conforms to various UNIX standards. In some cases, these standards conflict. This manpage describes the methods that programmers
and users must follow to have an application conform and execute according to a particular UNIX standard.
UNIX Standard Conformant Programmer Environment
The following table lists feature test macros and environment variables that must be defined while compiling an application. Both a fea-
ture test macro and an environment variable must be defined while compiling the application so that the application conforms and executes
according to a particular UNIX standard. Otherwise, the behavior is undefined.
Standard Feature Test Macros to be Environment variable
defined during compilation to be set
UNIX 95 _XOPEN_SOURCE_EXTENDED=1 UNIX95 or
UNIX_STD=95 or
UNIX_STD=1995
UNIX 2003 _XOPEN_SOURCE=600 UNIX_STD=2003
The compiler uses the feature test macros to obtain the appropriate namespace from the header files. The compiler uses the environment
variable to link in an appropriate object file to the executable. Using the environment variable customizes libc to match UNIX standards
for various functions.
If an application has already been compiled for default HP-UX behavior or for one particular standard, and needs to change to a particular
UNIX standard behavior, recompile the application as specified in the above table.
For an HP-UX command to conform to a particular UNIX standard behavior, the application has to set the corresponding environment variable
as specified in the above table before executing that command.
UNIX Standard Conformant User Environment
To enable a particular UNIX standard conformant user environment, set the corresponding environment variable as defined in the above table.
EXAMPLES
The following examples shows an application example. To have the system be conformant to UNIX2003 behavior, set the environment variable
to and define the feature test macro before compilation.
The following example changes the command to have UNIX95 behavior by setting one of the environment variables to or to before executing
that command. There are three ways of setting the environment variable for UNIX95:
or
or
SEE ALSO cc(1), stdsyms(5).
standards(5)