Sponsored Content
Full Discussion: Network interface-
Special Forums IP Networking Network interface- Post 302643389 by jlliagre on Saturday 19th of May 2012 10:10:07 AM
Old 05-19-2012
eth1 is here the default NAT interface. There is no risk of conflict as there is no real network, just the host side at 10.0.2.2 and the guest at 10.0.2.15.

Last edited by jlliagre; 05-19-2012 at 12:07 PM..
This User Gave Thanks to jlliagre For This Post:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies

3. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies

4. Solaris

Network interface not found ?

Hello, I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else. - I dont have any /etc/hostnames.xxx - ifconfig -a shows only the loopback - kstat -c net shows only the loopback ... Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies

5. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

7. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
GRUB-RENDER-LABEL(1)                                               User Commands                                              GRUB-RENDER-LABEL(1)

NAME
grub-render-label - generate a .disk_label for Apple Macs. SYNOPSIS
grub-render-label [OPTION...] [OPTIONS] DESCRIPTION
Render Apple .disk_label. -b, --bgcolor=COLOR use COLOR for background -c, --color=COLOR use COLOR for text -f, --font=FILE use FILE as font (PF2). -i, --input=FILE read text from FILE. -o, --output=FILE set output filename. Default is STDOUT -t, --text=STRING set the label to render -v, --verbose print verbose messages. -?, --help give this help list --usage give a short usage message -V, --version print program version Mandatory or optional arguments to long options are also mandatory or optional for any corresponding short options. REPORTING BUGS
Report bugs to <bug-grub@gnu.org>. SEE ALSO
The full documentation for grub-render-label is maintained as a Texinfo manual. If the info and grub-render-label programs are properly installed at your site, the command info grub-render-label should give you access to the complete manual. grub-render-label (GRUB) 2.02-2ubuntu8.3 July 2018 GRUB-RENDER-LABEL(1)
All times are GMT -4. The time now is 10:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy