05-19-2012
eth1 is here the default NAT interface. There is no risk of conflict as there is no real network, just the host side at 10.0.2.2 and the guest at 10.0.2.15.
Last edited by jlliagre; 05-19-2012 at 12:07 PM..
This User Gave Thanks to jlliagre For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
gchem3d
GCHEM3D(1) gnome-chemistry-utils GCHEM3D(1)
NAME
gchem3d - a small chemical viewer application
SYNOPSIS
gchem3d [OPTION(S)...] [FILE...]
DESCRIPTION
gchem3d is a small chemical viewer application, which can show several chemical file formats.
OPTIONS
The following options are accepted:
-b COLOR, --bgcolor=COLOR
Use the given color as background color. COLOR can be one of "black" (default), "white", "#rrggbb" (don't forget to escape the "#"
character in the shell).
-d MODEL, --display3d=MODEL
Choose how molecules are displayed. MODEL can be one of "BallnStick" (default), "SpaceFill".
-?, --help
Show application help options.
--help-all, --help-*
Print all or just a group of help options. These options are not documented here. Instead see gtk-options(7) and gnome-options(7).
-v, --version
Print gchem3d version information.
SEE ALSO
gnome-options(7), gtk-options(7)
AUTHORS
Jean Brefort <jean.brefort@normalesup.org>
Program author.
Daniel Leidert <daniel.leidert@wgdd.de>
Manpage author.
COPYRIGHT
Copyright (C) 2002-2007 Jean Brefort
Copyright (C) 2004-2007 Daniel Leidert
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 or any
later version published by the Free Software Foundation.
gcu 0.12 $Date: 2009-03-19 10:53:47 +0100 (jeu. 19 mars 2009) $ GCHEM3D(1)