05-19-2012
Please, I have another question, I'm working on VirtualBox, I have two network cards, one for LAN and one for the NAT access mode that allows me to connect to Internet, how to know which card goes with which IP address?
and if
Quote:
eth1 Link encap:Ethernet HWaddr 08:00:27:3a:0d:6b
inet addr:192.168.56.102 Bcast:192.168.56.255 Mask:255.255.255.0
correspond to network card LAN or network card NAT?
Thank you so much
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
4. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
pcapinfo
PCAPINFO(1p) User Contributed Perl Documentation PCAPINFO(1p)
NAME
pcapinfo - Prints detailed information about the network devices
SYNOPSIS
pcapinfo
OPTIONS
None.
DESCRIPTION
pcapinfo prints detailed information about the network devices and Pcap library available on the current host. Here is an example:
Host information
----------------
Hostname : fangorn.maddingue.net
Aliases : fangorn.local fangorn
Pcap version : libpcap version 0.8.3
Devices information
-------------------
Device eth0 (default)
Description : No description available
Link type : Ethernet, no autonegotiation, 10baseT-HD, link ok
Hardware address : 00:0c:6e:0a:c3:ca
Network address : 10.0.1.51
Network mask : 255.255.255.0
Flags : up running broadcast multicast
Device eth1
Description : No description available
Link type : Ethernet, no autonegotiation, 10baseT-HD, link ok
Hardware address : 00:26:54:0a:d8:4d
Network address : 192.168.1.51
Network mask : 255.255.255.0
Flags : up running broadcast multicast
The device marked as "(default)" is the one returned when calling "Net::Pcap::lookupdev()"
Some information like the link type can only be gathered with administrative privileges.
AUTHOR
Sebastien Aperghis-Tramoni, <sebastien@aperghis.net>
COPYRIGHT
Copyright (C) 2005, 2006, 2007, 2008 Sebastien Aperghis-Tramoni. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.14.2 2008-01-01 PCAPINFO(1p)