05-16-2012
yes but with 256mb there will be no GUI installer, only textmode. maybe not wanted for a workstation. but should work if no GUI is needed.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
5. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
6. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
7. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
8. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
9. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT DEBIAN
lv2soname
LV2SONAME(1) General Commands Manual LV2SONAME(1)
NAME
lv2soname - script which can be used in your build system to translate a linker option into the soname
DESCRIPTION
This manual page documents briefly the lv2soname command. This manual page was written for the Debian distribution because the original
program does not have a manual page.
lv2soname script can be used in your build system to translate a linker option (e.g. -lgtkmm2.4) into the soname (e.g. libgtkmm-2.4.so.1)
for the shared library that ld will link to when given that command line option. It will generate the RDF triples needed to tell hosts
that the library with that soname must never be unloaded even after your plugin GUI library has been unloaded.
e.g. $ lv2soname '<http://my.gui>' '<http://lv2plug.in/ns/lv2core#requiredFeature>' -lgtkmm-2.4
If the script for some reason can't determine the soname it will instead generate the RDF needed to tell the host to never unload the GUI
library at all.
However pretty much the same thing can be done by linking the plugin GUI using the -z nodelete linker option, which will keep the GUI
library loaded even after the host runs dlclose(), requiring no extra support from the host. So lv2soname is deprecated and will be
removed in the next major version release.
For more information please visit http://ll-plugins.nongnu.org
AUTHOR
lv2soname was written by Lars Luthman <lars.luthman@gmail.com>.
This manual page was written by Jaromir Mike <mira.mikes@seznam.cz>, for the Debian project (but may be used by others).
May 12, 2010 LV2SONAME(1)