05-16-2012
looks like a hardware error... so there won't be much that you can do... what i would try is a POST with MAX settings to see if the system can detect any errors during powerup. you'll need a seriell connection to the system to check the output of the POST.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
5. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
6. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
7. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
8. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
9. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT DEBIAN
bbmessage.cgi
BBMESSAGE.CGI(8) System Manager's Manual BBMESSAGE.CGI(8)
NAME
bbmessage.cgi - CGI utility used for proxying Xymon data over HTTP
SYNOPSIS
bbmessage.cgi
DESCRIPTION
bbmessage.cgi(8) is the server-side utility receiving Xymon messages sent by the bb(1) utility over an HTTP transport. The bb utility nor-
mally sends data over a dedicated TCP protocol, but it may use HTTP to go through proxies or through restrictive firewalls. In that case,
the webserver must have this CGI utility installed, which takes care of receiving the message via HTTP, and forwards it to a local Xymon
server through the normal Xymon transport.
The CGI expects to be invoked from an HTTP "POST" request, with the POST-data being the status-message. bbmessage.cgi simply collects all
of the POST data, and send it off as a message to the Xymon daemon running on IP 127.0.0.1. This destination IP currently cannot be
changed.
The CGI will return any output provided by the Xymon daemon back to the requestor as the response to the HTTP POST, so this allows for all
normal Xymon commands to work.
SECURITY
bbmesage.cgi will only send data to a Xymon server through the loopback interface, i.e. IP-address 127.0.0.1.
Access to the CGI should be restricted through webserver access controls, since the CGI provides no authentication at all to validate
incoming messages.
If possible, consider using the bbproxy(8) utility instead for native proxying of Xymon data between networks.
SEE ALSO
bb(1), bbproxy(8), xymon(7)
Xymon Version 4.2.3: 4 Feb 2009 BBMESSAGE.CGI(8)