05-16-2012
looks like a hardware error... so there won't be much that you can do... what i would try is a POST with MAX settings to see if the system can detect any errors during powerup. you'll need a seriell connection to the system to check the output of the POST.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
5. Solaris
Hi,
I have a Solaris 8.0 BLADE 150 machine. I have an onboard graphics alongwith an addon XVR500 graphics card. Now, when I use the motherboard graphics, I am not able to login to the XWINDOWS terminal, instead it stays on the console.
But, if I insert the monitor cable to the XVR500 port,... (2 Replies)
Discussion started by: angshuman_ag
2 Replies
6. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
7. Solaris
Hi everyone
can someone please explain to me how to install solaris 10 on a sunblade 1500 using cdrom?
Thanks for your assistance (1 Reply)
Discussion started by: cjashu
1 Replies
8. Solaris
Hello,
Ive just aquired a blade 150 off ebay.Im new to suns and are having a problem getting it to boot off the cdrom.Openboot continuously tries to do a network boot and I cant enter any commands.Im using an average pc keyboard and it definetly works.Thanks for any help.:wall: (3 Replies)
Discussion started by: chucky
3 Replies
9. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
10. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
LEARN ABOUT MOJAVE
curlopt_postfields
CURLOPT_POSTFIELDS(3) curl_easy_setopt options CURLOPT_POSTFIELDS(3)
NAME
CURLOPT_POSTFIELDS - specify data to POST to server
SYNOPSIS
#include <curl/curl.h>
CURLcode curl_easy_setopt(CURL *handle, CURLOPT_POSTFIELDS, char *postdata);
DESCRIPTION
Pass a char * as parameter, pointing to the full data to send in a HTTP POST operation. You must make sure that the data is formatted the
way you want the server to receive it. libcurl will not convert or encode it for you in any way. For example, the web server may assume
that this data is url-encoded.
The data pointed to is NOT copied by the library: as a consequence, it must be preserved by the calling application until the associated
transfer finishes. This behaviour can be changed (so libcurl does copy the data) by setting the CURLOPT_COPYPOSTFIELDS(3) option.
This POST is a normal application/x-www-form-urlencoded kind (and libcurl will set that Content-Type by default when this option is used),
which is commonly used by HTML forms. Change Content-Type with CURLOPT_HTTPHEADER(3).
You can use curl_easy_escape(3) to url-encode your data, if necessary. It returns a pointer to an encoded string that can be passed as
postdata.
Using CURLOPT_POSTFIELDS(3) implies CURLOPT_POST(3).
If CURLOPT_POSTFIELDS(3) is explicitly set to NULL then libcurl will get the POST data from the read callback. If you want to send a zero-
byte POST set CURLOPT_POSTFIELDS(3) to an empty string, or set CURLOPT_POST(3) to 1 and CURLOPT_POSTFIELDSIZE(3) to 0.
Using POST with HTTP 1.1 implies the use of a "Expect: 100-continue" header. You can disable this header with CURLOPT_HTTPHEADER(3) as
usual.
To make multipart/formdata posts (aka RFC2388-posts), check out the CURLOPT_HTTPPOST(3) option combined with curl_formadd(3).
DEFAULT
NULL
PROTOCOLS
HTTP
EXAMPLE
CURL *curl = curl_easy_init();
if(curl) {
const char *data = "data to send";
curl_easy_setopt(curl, CURLOPT_URL, "http://example.com");
/* size of the POST data */
curl_easy_setopt(curl, CURLOPT_POSTFIELDSIZE, 12L);
/* pass in a pointer to the data - libcurl will not copy */
curl_easy_setopt(curl, CURLOPT_POSTFIELDS, data);
curl_easy_perform(curl);
}
AVAILABILITY
Always
RETURN VALUE
Returns CURLE_OK
SEE ALSO
CURLOPT_POSTFIELDSIZE(3), CURLOPT_READFUNCTION(3),
libcurl 7.54.0 June 11, 2016 CURLOPT_POSTFIELDS(3)