Sponsored Content
Operating Systems Solaris Disks aren't showing up in Solaris/OBP Post 302637359 by bstring on Tuesday 8th of May 2012 07:02:33 PM
Old 05-08-2012
Update: hicksd8 you were correct, it was a raid configuration issue. I installed MegaCLI from LSI and I was able to see that there were only two logical drives configured. I configured the rest and I am now able to see the drives from within the OS.

Thanks so much for the help!
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Sun Solaris OBP Question

Hi, Does anyone know where i can find information on openboot prompt. My machine boot up with the number 1 ok. What does that mean? Any kind of help will be nice. Thanks in advance (4 Replies)
Discussion started by: souldier
4 Replies

2. Filesystems, Disks and Memory

re-partition disks on solaris

hi all, i was wondering if i have some volume manager and i want to format all partitions/disks and re-create new slices can i use regular format command or what? i think veritas volume manager is already installed. (2 Replies)
Discussion started by: Bashar
2 Replies

3. Solaris

Solaris x86 - 2 new disks

Have a compaq dl380 proliant installed with solaris.. It has a smart array 5i controller.. currently I have 2 18gb disks - mirrored as far as I can see... I have just put in 2 36gb disks (just physically put in) How do I get solaris to recognise them so I can use them? format command - only... (2 Replies)
Discussion started by: frustrated1
2 Replies

4. Solaris

Hard disks in solaris

I need to insert a new hard disk into a Sun Fire v210 machine. The (only) internal disk which is already in the machine is part number XRA-SC1CB-73G10K (DISK DRIVE ASSY. 73GB, 10K RPM, with SPUD BRACKET). I also have nearly endless access to IBM hard disks at extremely low prices and would there... (2 Replies)
Discussion started by: sprellari
2 Replies

5. Solaris

OBP on Solaris 10-intel

Hi All, How can I go to OBP on Solaris 10-intel? I tried doing ctrl+c or ctrl+break, it won't go to the "ok" prompt. Thanks in advance, itik (6 Replies)
Discussion started by: itik
6 Replies

6. Solaris

disks in solaris

whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies

7. Shell Programming and Scripting

getting number of disks in solaris

Friends, i have used the following code to get the number of disks in solaris echo | pfexec format | egrep -v "Searching|AVAILABLE|Specify|^$|@" | wc -l is there a better way to get the same result (5 Replies)
Discussion started by: achak01
5 Replies

8. Solaris

Not showing n/w interface name in Solaris with ifconfig -a

hi frineds in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names . after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies

9. Solaris

list all solaris Disks

Hi Guy's can anyone advise me .. I have mapped some of EMC devices from EMC Storage to Sun Solaris server and I want to list all the disk which are assigned from the storage can anyone advise me with the command how to can I list all the disk in Solaris Thanks .. (2 Replies)
Discussion started by: roooooot
2 Replies

10. Solaris

Virtual disks are not showing up in LDom

I have an Oracle VM set up with 1 virtual disk. I am trying to add 2 new disks to it. I was able to successfully add 1 (it appears when I run "format" in the VM) but when I add the second and third disks they do not appear in my VM. Here are the commands I ran: ldm add-vdsdev... (3 Replies)
Discussion started by: unblockable
3 Replies
MPT(4)							   BSD Kernel Interfaces Manual 						    MPT(4)

NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device mpt Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): mpt_load="YES" DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers. HARDWARE
The following controllers are supported by the mpt driver: o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI) o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA) o LSI Logic FC909 (1Gb/s Fibre Channel) o LSI Logic FC909A (Dual 1Gb/s Fibre Channel) o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel) o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel) o LSI Logic FC949X (Dual 4Gb/s Fibre Channel) o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express) The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including: o Dell PowerEdge 1750 thru 2850 o IBM eServer xSeries 335 These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports. The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at best. The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the FC949ES card. This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required. SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8) LSI Logic Website, http://www.lsilogic.com/. HISTORY
The mpt driver first appeared in FreeBSD 4.6. AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>. Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements. BUGS
BSD
May 13, 2010 BSD
All times are GMT -4. The time now is 06:50 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy