Sponsored Content
Operating Systems Solaris Sunfire V440 could not correctly recognize HD Post 302634425 by BigG on Thursday 3rd of May 2012 10:23:22 AM
Old 05-03-2012
Thanks for all you replied.

The new hard drive we got from Sun service provider. It's a genuine sun hard drive for V440.

If I just run "format -e" and select disk#2, then it's hung (forever? may be). Ctrl+c will break it, but never go through.

I have no chance to change the label.

Last time I was able to, but there are only 2 options:

1. auto
2. enter the hard drive specifications, such as head/cylinders/etc
 

10 More Discussions You Might Find Interesting

1. Solaris

Sunfire 280R Can't Recognize Floppy Drive

Greetings all, I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies

2. Solaris

Can't get ok prompt on V440

Hello all, This is probably a commonly asked question, but it has me stumped. I have a V440 which upon bootup gives me the option of getting into ALOM with #. I don't have the ALOM password so I want to re-install Solaris 10. When connected to the Management serial interface (on the PCI... (3 Replies)
Discussion started by: juanj
3 Replies

3. Solaris

SunFire V440 Quad gigabit ce1 won't run Gig

Hi there. My first time posting so apologies for any indescretions in advance. :o I've got two SunFire V440 servers running Solaris 5v10. Both have a quad Gigabit ethernet card fitted, both have the same symptom; that is, I can't get the first port ce1 to run Gigabit. Motherboard ports are ce0 and... (10 Replies)
Discussion started by: fixit9660
10 Replies

4. Solaris

video card for a V440

I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies

5. Solaris

SUN V440 Question

I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies

6. Solaris

V210 to V440

I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440. I would like to avoid reinstall on the V440 for many reasons. Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies

7. Solaris

Need ideas what is wrong with v440

Hello everyone, I'm here today looking for help... I have a SunFire v440 running Solaris 9 at work that manages the SCSI tape drives(LTO3) in our L700 tape library (runs SAMFS). I went into work today and found the machine was ping-able but I could not connect to it via SSH and could not... (7 Replies)
Discussion started by: mainegeek
7 Replies

8. Solaris

V210 to V440

I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies

9. Solaris

available PCI slots on v440

How do I find any available PCI slots on a v440? When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used. ================================= IO Devices ================================= Bus Freq Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies

10. Solaris

Solaris V440 keeps crashing

Hi, I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file. ... (1 Reply)
Discussion started by: samnyc
1 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 01:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy