Sponsored Content
Operating Systems Solaris Disks aren't showing up in Solaris/OBP Post 302630979 by hicksd8 on Thursday 26th of April 2012 02:45:28 PM
Old 04-26-2012
I'm beginning to think that these drives cannot be seen by the system because there's a connection/hardware problem.

Format -e should see them; so should probe-scsi-asll.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Sun Solaris OBP Question

Hi, Does anyone know where i can find information on openboot prompt. My machine boot up with the number 1 ok. What does that mean? Any kind of help will be nice. Thanks in advance (4 Replies)
Discussion started by: souldier
4 Replies

2. Filesystems, Disks and Memory

re-partition disks on solaris

hi all, i was wondering if i have some volume manager and i want to format all partitions/disks and re-create new slices can i use regular format command or what? i think veritas volume manager is already installed. (2 Replies)
Discussion started by: Bashar
2 Replies

3. Solaris

Solaris x86 - 2 new disks

Have a compaq dl380 proliant installed with solaris.. It has a smart array 5i controller.. currently I have 2 18gb disks - mirrored as far as I can see... I have just put in 2 36gb disks (just physically put in) How do I get solaris to recognise them so I can use them? format command - only... (2 Replies)
Discussion started by: frustrated1
2 Replies

4. Solaris

Hard disks in solaris

I need to insert a new hard disk into a Sun Fire v210 machine. The (only) internal disk which is already in the machine is part number XRA-SC1CB-73G10K (DISK DRIVE ASSY. 73GB, 10K RPM, with SPUD BRACKET). I also have nearly endless access to IBM hard disks at extremely low prices and would there... (2 Replies)
Discussion started by: sprellari
2 Replies

5. Solaris

OBP on Solaris 10-intel

Hi All, How can I go to OBP on Solaris 10-intel? I tried doing ctrl+c or ctrl+break, it won't go to the "ok" prompt. Thanks in advance, itik (6 Replies)
Discussion started by: itik
6 Replies

6. Solaris

disks in solaris

whats the command to find name of all disks. Is it iostat -En ? (1 Reply)
Discussion started by: vikashtulsiyan
1 Replies

7. Shell Programming and Scripting

getting number of disks in solaris

Friends, i have used the following code to get the number of disks in solaris echo | pfexec format | egrep -v "Searching|AVAILABLE|Specify|^$|@" | wc -l is there a better way to get the same result (5 Replies)
Discussion started by: achak01
5 Replies

8. Solaris

Not showing n/w interface name in Solaris with ifconfig -a

hi frineds in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names . after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies

9. Solaris

list all solaris Disks

Hi Guy's can anyone advise me .. I have mapped some of EMC devices from EMC Storage to Sun Solaris server and I want to list all the disk which are assigned from the storage can anyone advise me with the command how to can I list all the disk in Solaris Thanks .. (2 Replies)
Discussion started by: roooooot
2 Replies

10. Solaris

Virtual disks are not showing up in LDom

I have an Oracle VM set up with 1 virtual disk. I am trying to add 2 new disks to it. I was able to successfully add 1 (it appears when I run "format" in the VM) but when I add the second and third disks they do not appear in my VM. Here are the commands I ran: ldm add-vdsdev... (3 Replies)
Discussion started by: unblockable
3 Replies
NTFS-3G.PROBE(8)					      System Manager's Manual						  NTFS-3G.PROBE(8)

NAME
ntfs-3g.probe - Probe an NTFS volume mountability SYNOPSIS
ntfs-3g.probe <--readonly|--readwrite> volume DESCRIPTION
The ntfs-3g.probe utility tests a volume if it's NTFS mountable read-only or read-write, and exits with a status value accordingly. The volume can be a block device or image file. OPTIONS
Below is a summary of the options that ntfs-3g.probe accepts. -r, --readonly Test if the volume can be mounted read-only. -w, --readwrite Test if the volume can be mounted read-write. -h, --help Display help and exit. EXAMPLE
Test if /dev/sda1 can be mounted read-write: ntfs-3g.probe --readwrite /dev/sda1 EXIT CODES
The exit codes are as follows: 0 Volume is mountable. 11 Syntax error, command line parsing failed. 12 The volume doesn't have a valid NTFS. 13 Inconsistent NTFS, hardware or device driver fault, or unsetup SoftRAID/FakeRAID hardware. 14 The NTFS partition is hibernated. 15 The volume was not cleanly unmounted. 16 The volume is already exclusively opened and in use by a kernel driver or software. 17 Unsetup SoftRAID/FakeRAID hardware. 18 Unknown reason. 19 Not enough privilege to mount. 20 Out of memory. 21 Unclassified FUSE error. KNOWN ISSUES
Please see http://ntfs-3g.org/support.html for common questions and known issues. If you think you have found an undocumented problem in the latest release of the software then please send an email describing it in detail. You can contact the development team on the ntfs-3g-devel@lists.sf.net address. AUTHORS
ntfs-3g.probe was written by Szabolcs Szakacsits (szaka@ntfs-3g.org). THANKS
Alon Bar-Lev has integrated the utility into the NTFS-3G build process and tested it with Erik Larsson before the public release. SEE ALSO
ntfs-3g(8) ntfs-3g.probe 2010.3.6 January 2008 NTFS-3G.PROBE(8)
All times are GMT -4. The time now is 02:34 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy