Hi,
I am having problems using grep to extract only 3,4 or 5 digit numbers from a text file, using:
grep '\<\{3,5\}\>' test.txt
or
grep '\{3,5\}' test.txt
or
egrep '{3,5}' test.txt
I would appreciate any help that anyone can give me
thanks (1 Reply)
Hi, All -
script1.awk contains the following script:
BEGIN {
printf "The following are directory files:"
"ls -l | grep '^d' | {print $0}"
printf "There were "NR" directories in this list."
}
When I run the script, Here is what I get:
$ awk -f... (4 Replies)
How do I get this to work?
cat somefile | grep "-rw-r--r-- 1 root wheel 287 Sep 10 15:12 shells~"
This is the the desired output
-rw-r--r-- 1 root wheel 287 Sep 10 15:12 shells~
I basically want an exact match of the line I am grepping for, the special characters and... (5 Replies)
Hello,
i have a file called test
hello1
"how" are you4
good"bye"
good7bye
i am trying to print all lines from test that either end with a digit or contain a double quote character anywhere on the line.
i did
grep -n '$' test and was able to print lines ending with digits.
i also did... (2 Replies)
I have a file with a lot of lines (a lot!) that contain 10 digits between double quotes. ie "1726937489". The digits are random throughout, but always contain ten digits.
I can not for the life of me, (via scouring the internet and grep how-to manuals) figure out how to find this when I search.... (3 Replies)
Hello all! I've looked all over the internet and this site and have come up a loss with an easy way to make a bash script to do what I want to do. I have a file with a naming convention as follows:
2012-01-18 string of words here 123.jpg
2012-01-18 string of words here 1234.jpg
2012-01-18... (2 Replies)
Hi
Can any one pls tell me how to grep this line
POPULATION,69691,20120509
I want the number 69691 from the above line.
How to grep from the first comma till the next comma.
Thank You.:confused: (8 Replies)
I'm trying to grep lines where the digits at the end of each line are greater than digits. Tried this but it will only allow me to specify 2 digits. Any ideas would greatly be appreciated. grep -i '\<\{3,4,5\}\>' file
---------- Post updated at 05:58 PM ---------- Previous update was at 05:41... (1 Reply)
Hi All ,
I am having an input file as stated below
5728 U_TOP_LOGIC/U_CM0P/core/u_cortexm0plus/u_top/u_sys/u_core/r03_q_reg_20_/Q 011
611 U_TOP_LOGIC/U_CM0P/core/u_cortexm0plus/u_top/u_sys/u_core/r04_q_reg_20_/Q 011
3486... (4 Replies)
Discussion started by: kshitij
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)