04-21-2012
Virtual machines in vmware requires reset of the vlan
I have virtual machines in the vmware environment that run either windows or linux that loose conncetivity and every time i have to change their vlan to vm network and latter join them to original vlan to gain connectivity.
Advice
Last edited by amwai; 04-21-2012 at 03:59 AM..
7 More Discussions You Might Find Interesting
1. Windows & DOS: Issues & Discussions
Hi,
I was required to do a backup of a virtual machine that runs on vmware. The guest operating system is windows, and the host is windows too. I have to backup the whole directory of the virtual machine (say in linux it'll be in /var/lib/vmware/virtual machines/) to a linux server.
Initially... (0 Replies)
Discussion started by: 60doses
0 Replies
2. Linux
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Discussion started by: bakunin
0 Replies
3. UNIX for Dummies Questions & Answers
I'm trying to research interpreters and I can't find much info on Pcode or how or why it is used.
Thanks in advance!:wall: (2 Replies)
Discussion started by: theKbStockpiler
2 Replies
4. Ubuntu
Hello,
I installed two virtual machines ubuntu10 on VM VirtualBox .
Please, what are the steps to make a ping from one of these two machines on the other (the configurations )?
Thank you. (4 Replies)
Discussion started by: chercheur111
4 Replies
5. Virtualization and Cloud Computing
Hi All
How would you send a solaris virtual machine in vmware esx, a break signal? :confused: (0 Replies)
Discussion started by: jakerock
0 Replies
6. UNIX and Linux Applications
Help with Install KVM and Create Virtual Machines VMWare In PC.
I want to lean KVM bios Logical Volume Management by KVM and other problem fix remotely.So,I want to practice on my PC.It,s Possible then how?
Thank you (0 Replies)
Discussion started by: domaingood
0 Replies
7. UNIX for Beginners Questions & Answers
Hi All,
Is there any way I can prioritize my VMs when there is resource crunch in host machine so that some VMs will be allocated more vcpu, more memory than other VMs in kvm/qemu hypervisor based virtual machines?
Lets say in my cloud environment my Ubuntu 16 compute hosts are running some... (0 Replies)
Discussion started by: SanjayK
0 Replies
LEARN ABOUT FREEBSD
if_epair
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5), rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD