04-20-2012
Quote:
Originally Posted by
Peasant
Are you sure this is correct in your setup
/etc/sysconfig/network-scripts-ifcfg-bond0
Should be (atleast on my RHEL 6.2 Santiago)
/etc/sysconfig/network-scripts/ifcfg-bond0
Yes, this was just a type that i made while posting it here.
10 More Discussions You Might Find Interesting
1. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
2. Emergency UNIX and Linux Support
Hi All Linux Experts ,
Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Discussion started by: babinlonston
4 Replies
3. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
4. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
5. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
6. Red Hat
I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
Discussion started by: Sahil Sharma
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
8. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
9. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
10. Solaris
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT DEBIAN
smpppd-ifcfg
SMPPPD-IFCFG(8) SMPPPD SMPPPD-IFCFG(8)
NAME
smpppd-ifcfg - SuSE Meta PPP Daemon
DESCRIPTION
smpppd-ifcfg is a daemon that controls a single dialup connection to the internet. It does so by starting and controlling the pppd. The
configuration of the dialup connections is done by YaST2.
smpppd-ifcfg is not intended for direct use. Use ifup and ifdown or a frontend like cinternet , qinternet or kinternet instead.
OPTIONS
These options are recognized by smpppd-ifcfg. If a long option shows an argument as mandatory, then it is mandatory for the equivalent
short option also.
--up Bring the connection up. This is the default action.
--down Bring the connection down.
--status
Report status of the connection.
-i, --ifcfg=NAME
Specify the ifcfg file to use. This option is mandatory.
-p, --provider=NAME
Specify the provider file to use.
--detach
Detach from the controlling terminal. This is the default.
--nodeatch
Don't detach from the controlling terminal.
-d, --debug
Turn on debugging.
--version
Show program version and exit.
--help Show help information and exit.
FILES
/etc/sysconfig/network/ifcfg-*
Configuration files for the interfaces.
/etc/sysconfig/network/providers/*
Configuration files for the providers.
/var/log/smpppd/ifcfg-xxx.log
Log file.
/var/log/smpppd/accounting.log
File containing accounting information.
/var/run/smpppd.ifcfg-xxx.pid
Pid file.
/var/lib/smpppd/ifcfg-xxx.info
Info file with various status information.
/var/run/smpppd/ifcfg-xxx
Socket to communicate with smpppd.
SEE ALSO
kinternet, qinternet, cinternet(1), accounting(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd(8).
AUTHOR
Arvin Schnell <arvin@suse.de>
SuSE December 2002 SMPPPD-IFCFG(8)