|
|
Sponsored Content
Operating Systems
Solaris
Sunfire V440 could not correctly recognize HD
Post 302626667 by fugitive on Thursday 19th of April 2012 02:38:47 PM
04-19-2012
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Greetings all,
I'm in a bit of a situation. I have this Sunfire 280R system that did not have a floppy drive in it, yet we needed one. We grabbed one from another Sun box we had laying around unused, and installed it. The system couldnt recognize it. Tried another floppy drive (non-sun) and... (4 Replies)
Discussion started by: snackiesmores
4 Replies
2. Solaris
Hello all,
This is probably a commonly asked question, but it has me stumped.
I have a V440 which upon bootup gives me the option of getting into ALOM with #. I don't have the ALOM password so I want to re-install Solaris 10.
When connected to the Management serial interface (on the PCI... (3 Replies)
Discussion started by: juanj
3 Replies
3. Solaris
Hi there. My first time posting so apologies for any indescretions in advance. :o I've got two SunFire V440 servers running Solaris 5v10. Both have a quad Gigabit ethernet card fitted, both have the same symptom; that is, I can't get the first port ce1 to run Gigabit. Motherboard ports are ce0 and... (10 Replies)
Discussion started by: fixit9660
10 Replies
4. Solaris
I am looking into getting some cards for the SunFire V440. Not sure how most folks go about this but I am assuming we can find compatible cards for this server platform without going through SUN. Do you guys recommend getting this video card from SUN? Yeah we got these servers without the video... (5 Replies)
Discussion started by: bluridge
5 Replies
5. Solaris
I have a SUN V440 and it is running Solaris 9 with two NICs in the box ce0 ce1. Is there any way to get full duplex 1000? I do I check to see what ce0 and ce1 is set at and if it is not set to full duplex 1000, how do I set it and do I have to reboot the system afterward? I am new to the SUN unix... (5 Replies)
Discussion started by: pmwayne01
5 Replies
6. Solaris
I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440.
I would like to avoid reinstall on the V440 for many reasons.
Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies
7. Solaris
Hello everyone,
I'm here today looking for help...
I have a SunFire v440 running Solaris 9 at work that manages the SCSI tape drives(LTO3) in our L700 tape library (runs SAMFS).
I went into work today and found the machine was ping-able but I could not connect to it via SSH and could not... (7 Replies)
Discussion started by: mainegeek
7 Replies
8. Solaris
I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies
9. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
10. Solaris
Hi,
I have Sun Solaris V440, every two days or so, the system crashes and it's at OK prompt. After that I do the FSCK and clear all the bad sectors. Then system stays up for close to 48 hours. Then it crashes again. I checked the logs and I don't see anything under /var/adm/messages file.
... (1 Reply)
Discussion started by: samnyc
1 Replies
LEARN ABOUT DEBIAN
cd-drive
CD-DRIVE(1) User Commands CD-DRIVE(1) NAME
cd-drive - manual page for cd-drive version 0.83 i686-pc-linux-gnu SYNOPSIS
cd-drive OPTION... Shows CD-ROM drive characteristics. DESCRIPTION
-d, --debug=INT Set debugging to LEVEL -i, --cdrom-device[=DEVICE] show only info about CD-ROM device -q, --quiet Don't produce warning output -V, --version display version and copyright information and exit Help options: -?, --help Show this help message --usage Display brief usage message AUTHOR
Rocky Bernstein rocky@gnu.org COPYRIGHT
Copyright (C) 2003, 2004, 2005, 2007, 2008, 2011 R. Bernstein This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. Have driver: GNU/Linux ioctl and MMC driver Have driver: cdrdao (TOC) disk image driver Have driver: bin/cuesheet disk image driver Have driver: Nero NRG disk image driver Default CD-ROM device: /dev/scd0 SEE ALSO
cd-info(1) for information about the CD inside a CD-ROM. cd-drive version 0.83 i686-pc-linux-gnu October 2011 CD-DRIVE(1)