04-19-2012
Quote:
Originally Posted by
Peasant
It is perhaps a silly question but have ran modprobe bonding ?
Hi Peasant,
Yes i have ran modprobe bonding. But the issue i am facing that it works fine when system boots up but ASA i restart the network service the whole thing stops, the bond0 interface never comes up.
10 More Discussions You Might Find Interesting
1. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
2. Emergency UNIX and Linux Support
Hi All Linux Experts ,
Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Discussion started by: babinlonston
4 Replies
3. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
4. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
5. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
6. Red Hat
I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
Discussion started by: Sahil Sharma
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
8. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
9. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
10. Solaris
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT DEBIAN
ifenslave-2.6
IFENSLAVE(8) BSD System Manager's Manual IFENSLAVE(8)
NAME
ifenslave -- Attach and detach slave network devices to a bonding device.
SYNOPSIS
ifenslave [-acdfhuvV] [--all-interfaces] [--change-active] [--detach] [--force] [--help] [--usage] [--verbose] [--version] master slave ...
DESCRIPTION
ifenslave is a tool to attach and detach slave network devices to a bonding device. A bonding device will act like a normal Ethernet network
device to the kernel, but will send out the packets via the slave devices using a simple round-robin scheduler. This allows for simple load-
balancing, identical to "channel bonding" or "trunking" techniques used in switches.
The kernel must have support for bonding devices for ifenslave to be useful.
OPTIONS
-a, --all-interfaces
Show information about all interfaces.
-c, --change-active
Change active slave.
-d, --detach
Removes slave interfaces from the bonding device.
-f, --force
Force actions to be taken if one of the specified interfaces appears not to belong to an Ethernet device.
-h, --help
Display a help message and exit.
-u, --usage
Show usage information and exit.
-v, --verbose
Print warning and debug messages.
-V, --version
Show version information and exit.
If not options are given, the default action will be to enslave interfaces.
EXAMPLE
The following example shows how to setup a bonding device and enslave two real Ethernet devices to it:
# modprobe bonding
# ifconfig bond0 192.168.0.1 netmask 255.255.0.0
# ifenslave bond0 eth0 eth1
AUTHOR
ifenslave was originally written by Donald Becker <becker@cesdis.gsfc.nasa.gov>, and has since been updated by various kernel developers.
This manual page was written by Guus Sliepen <guus@debian.org> for the Debian GNU/Linux system.
Debian GNU/Linux June 1, 2019 Debian GNU/Linux