|
|
Sponsored Content
Special Forums
IP Networking
Channel bonding Issue - Bond0 interface not getting up in on RHEL6
Post 302626457 by DukeNuke2 on Thursday 19th of April 2012 10:18:10 AM
04-19-2012
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
2. Emergency UNIX and Linux Support
Hi All Linux Experts ,
Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Discussion started by: babinlonston
4 Replies
3. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
4. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
5. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
6. Red Hat
I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
Discussion started by: Sahil Sharma
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
8. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
9. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
10. Solaris
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT V7
fcp
fcp(7D) Devices fcp(7D) NAME
fcp - Fibre Channel protocol driver DESCRIPTION
The fcp driver is the upper layer protocol that supports mechanisms for transporting SCSI-3 commands over Fibre Channel. The fcp driver, which interfaces with the Sun Fibre Channel transport library fctl(7D), supports the standard functions provided by the SCSA interface. FILES
/kernel/drv/fcp 32-bit ELF kernel driver (x86) /kernel/drv/amd64/fcp 64-bit ELF kernel driver (x86) /kernel/drv/sparcv9/fcp 64-bit ELF kernel driver (SPARC) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |SPARC | +-----------------------------+-----------------------------+ |Interface stability |Unknown | +-----------------------------+-----------------------------+ |Availability |SUNWfcp | +-----------------------------+-----------------------------+ SEE ALSO
prtconf(1M), driver.conf(4), fctl(7D), fp(7D), usoc(7D) Writing Device Drivers Fibre Channel Physical and Signaling Interface (FC-PH) ANSI X3.230: 1994 Fibre Channel Generic Services (FC-GS-2) Project 1134-D Fibre Channel Arbitrated Loop (FC-AL) ANSI X3.272-1996 Fibre Channel Protocol for SCSI (FCP) ANSI X3.269-1996 SCSI-3 Architecture Model (SAM) Fibre Channel Private Loop SCSI Direct Attach (FC-PLDA) ANSI X3.270-1996 Fabric Loop Attachment (FC-FLA), NCITS TR-20:1998 SunOS 5.10 20 Oct 2004 fcp(7D)