04-19-2012
i don't have access to the machines anymore... i installed them at customer datacenter... the output of the bond config is from my documentation with some default ip...
10 More Discussions You Might Find Interesting
1. IP Networking
Hello,
I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave.
Example:
eth0 RX 123.2 GiB TX 22.5 GiB
eth1 RX 84.8 GiB TX 8.3 GiB
eth2... (3 Replies)
Discussion started by: TehOne
3 Replies
2. Emergency UNIX and Linux Support
Hi All Linux Experts ,
Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Discussion started by: babinlonston
4 Replies
3. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
4. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
5. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
6. Red Hat
I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
Discussion started by: Sahil Sharma
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
8. AIX
Hi Everyone,
Is it possible to configure bonding over bonded interface in AIX?
For example:
server has for NIC port:
ent0
ent1
ent2
ent3
First I create a EtherChannel ent4 from ent0 and ent1.
and then I create a EtherChannel ent5 from ent2 and ent3.
Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies
9. Linux
Respected Members,
We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies
10. Solaris
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)
NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO
ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)