Sponsored Content
Special Forums IP Networking Channel bonding Issue - Bond0 interface not getting up in on RHEL6 Post 302626457 by DukeNuke2 on Thursday 19th of April 2012 10:18:10 AM
Old 04-19-2012
i don't have access to the machines anymore... i installed them at customer datacenter... the output of the bond config is from my documentation with some default ip...
 

10 More Discussions You Might Find Interesting

1. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2... (3 Replies)
Discussion started by: TehOne
3 Replies

2. Emergency UNIX and Linux Support

RHEL6.2 Santiago Audio Issue

Hi All Linux Experts , Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant... (4 Replies)
Discussion started by: babinlonston
4 Replies

3. Red Hat

BONDING with Flapping issue!

Hi team, I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies

4. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies

5. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies

6. Red Hat

Multipath issue in RHEL6.5 32-bit

I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason? (1 Reply)
Discussion started by: Sahil Sharma
1 Replies

7. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

8. AIX

Is it possible to configure bonding over bonded interface in AIX?

Hi Everyone, Is it possible to configure bonding over bonded interface in AIX? For example: server has for NIC port: ent0 ent1 ent2 ent3 First I create a EtherChannel ent4 from ent0 and ent1. and then I create a EtherChannel ent5 from ent2 and ent3. Can I create a EtherChannel... (1 Reply)
Discussion started by: nnnnnnine
1 Replies

9. Linux

Issue in Bonding during Reboot(Linux)

Respected Members, We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other... (0 Replies)
Discussion started by: Mudit Bansal
0 Replies

10. Solaris

Issue with Fiber Channel cards in Solaris

hi everone i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
STRMSGSZ(5)							File Formats Manual						       STRMSGSZ(5)

NAME
STRMSGSZ - maximum size of streams message data (bytes) VALUES
Failsafe Default Allowed values Recommended values DESCRIPTION
This tunable limits the number of bytes of message data that can be inserted by or in the data portion of any streams message on the sys- tem. If the tunable is set to zero, there is no limit on how many bytes can be placed in the data segment of the message. returns if the buffer being sent is larger than the current value of segments the data into multiple messages. Who Is Expected to Change This Tunable? Any customer. Restrictions on Changing Changes to this tunable take effect at next reboot. When Should the Value of This Tunable Be Raised? The tunable should be increased by any customer if the customer's STREAMS module/driver(s) require a longer message size in the data por- tion than the current value. What Are the Side Effects of Raising the Value of This Tunable? The kernel will use more memory. During low memory situations, it may bring down system performance due to frequent swapping. When Should the Value of This Tunable Be Lowered? The tunable could be lowered by any customer if the customer's STREAMS module/driver(s) do not require a longer message size in the data portion than the current value. What Are the Side Effects of Lowering the Value of This Tunable? Possible improper functioning in any of the STREAMS module/driver(s). Possible performance degradation, particularly in networking. What Other Tunable Should Be Changed at the Same Time as This One? None. WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of HP-UX. Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation, some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun- able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was factory installed on your system, see at AUTHOR
was developed by HP. Tunable Kernel Parameters STRMSGSZ(5)
All times are GMT -4. The time now is 11:53 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy