Channel bonding Issue - Bond0 interface not getting up in on RHEL6 Post: 302626067

10 More Discussions You Might Find Interesting

1. IP Networking

Interface bonding / Link aggregation (Multiple)

Hello, I've been using mode 4 with four slaves, however looking at ifconfig showed that the traffic was not balanced correctly between the interfaces, the outgoing traffic has been alot higher on the last slave. Example: eth0 RX 123.2 GiB TX 22.5 GiB eth1 RX 84.8 GiB TX 8.3 GiB eth2...

2. Emergency UNIX and Linux Support

RHEL6.2 Santiago Audio Issue

Hi All Linux Experts , Need Urgent help , im using RHEL6.2 Santiago , While playing Song its not playing Properly its jerking Voice breaking breaking ... Cant Hear Properly , And im using Intel DG61HO Motherboard With intel i3 Processor , Please Help me to get fixed this issue ... And cant...

3. Red Hat

BONDING with Flapping issue!

Hi team, I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes,...

4. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB...

5. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are...

6. Red Hat

Multipath issue in RHEL6.5 32-bit

I am facing problems with native multipath of the OS RHEL 6.5 (32-bit). One of the two paths of random Logical disks are not going neither failing back unless we reboot the system.what could be the reason?

7. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your...

8. AIX

Is it possible to configure bonding over bonded interface in AIX?

Hi Everyone, Is it possible to configure bonding over bonded interface in AIX? For example: server has for NIC port: ent0 ent1 ent2 ent3 First I create a EtherChannel ent4 from ent0 and ent1. and then I create a EtherChannel ent5 from ent2 and ent3. Can I create a EtherChannel...

9. Linux

Issue in Bonding during Reboot(Linux)

Respected Members, We encountered an issue during node reboot when eth1 and eth5 of bond1 were behaving unusual(both eth1 and eth5 were in unknown states and ifdown and ifup were used to rectify). Please find the messages and configuration files as below and please let me know for any other...

10. Solaris

Issue with Fiber Channel cards in Solaris

hi everone i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but...

LEARN ABOUT CENTOS

ifenslave

IFENSLAVE(8)						    BSD System Manager's Manual 					      IFENSLAVE(8)

NAME

     ifenslave -- Attach and detach slave network devices to a bonding device.

SYNOPSIS

     ifenslave [-acdfhuvV] [--all-interfaces] [--change-active] [--detach] [--force] [--help] [--usage] [--verbose] [--version] master slave ...

DESCRIPTION

     ifenslave is a tool to attach and detach slave network devices to a bonding device.  A bonding device will act like a normal Ethernet network
     device to the kernel, but will send out the packets via the slave devices using a simple round-robin scheduler.  This allows for simple load-
     balancing, identical to "channel bonding" or "trunking" techniques used in switches.

     The kernel must have support for bonding devices for ifenslave to be useful.

OPTIONS

     -a, --all-interfaces
	     Show information about all interfaces.

     -c, --change-active
	     Change active slave.

     -d, --detach
	     Removes slave interfaces from the bonding device.

     -f, --force
	     Force actions to be taken if one of the specified interfaces appears not to belong to an Ethernet device.

     -h, --help
	     Display a help message and exit.

     -u, --usage
	     Show usage information and exit.

     -v, --verbose
	     Print warning and debug messages.

     -V, --version
	     Show version information and exit.
     If not options are given, the default action will be to enslave interfaces.

EXAMPLE

     The following example shows how to setup a bonding device and enslave two real Ethernet devices to it:

     # modprobe bonding
     # ifconfig bond0 192.168.0.1 netmask 255.255.0.0
     # ifenslave bond0 eth0 eth1

AUTHOR

     ifenslave was originally written by Donald Becker <becker@cesdis.gsfc.nasa.gov>, and has since been updated by various kernel developers.

     This manual page was written by Guus Sliepen <guus@debian.org> for the Debian GNU/Linux system.

								   May 31, 2019

10 More Discussions You Might Find Interesting

1. IP Networking

Interface bonding / Link aggregation (Multiple)

Discussion started by: TehOne

2. Emergency UNIX and Linux Support

RHEL6.2 Santiago Audio Issue

Discussion started by: babinlonston

3. Red Hat

BONDING with Flapping issue!

Discussion started by: leo_ultra_leo

4. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

Discussion started by: elliottlc