04-17-2012
Find out the failed disk
Hi Masters,
How to find out the failed disk in redhat linux (OR)
How to decalare whether our hard disk goes bad ?
My option is:
dmesg | grep "failed"
check in /var/log/messages with the kernel error.
Please corrrect me if im wrong.
And also i heard "smartctl" command. But it's difficult to understand. Please help me out how to use this command ...
Any reply(s) would be a great !!!
Thanks !
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
My WS boot disk has failed so when i want to boot system (by OK boot -s or Ok boot disk0 ) i get these mesgs:
disk read error
boot :can not find misc/sparc9v/krtld
boot:error loading interperetor (misc/sparc9v/krtld)
Elf64 read error.
boot failed.
although it's probed ,finally i try... (1 Reply)
Discussion started by: nikk
1 Replies
2. Solaris
Hi All,
Seems to be one of the disk has failed on my Solaris server.
How do i confirm that disk has really failed or not?
Here are alert details.
-------
iostat -En out/put
c1t3d0 Soft Errors: 1884 Hard Errors: 153 Transport Errors: 54
Vendor: FUJITSU Product:... (3 Replies)
Discussion started by: Naresh Kommina
3 Replies
3. Solaris
Dear all
Please can any one explain me how to replace failed disk in Solaris 10.
Please tell me the step by step procedure. (9 Replies)
Discussion started by: suneelieg
9 Replies
4. Solaris
-bash-3.00# zpool detach zonepool c1t1d0
cannot detach c1t1d0: only applicable to mirror and replacing vdevs
-bash-3.00# zpool remove zonepool c1t1d0
cannot remove c1t1d0: only inactive hot spares, cache, top-level, or log devices can be removed
-bash-3.00# zpool offline zonepool c1t1d0... (3 Replies)
Discussion started by: LittleLebowski
3 Replies
5. Boot Loaders
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
6. Linux
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
7. UNIX for Advanced & Expert Users
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
8. Solaris
I have an oldish Solaris 10 system (SunFire x4240), which due to a recent heating event in the server room, lost it's system disk.
I have rsync backups of all the other (data) disks, but apparently I do not have a backup of /. :-( I can start the machine up in failsafe mode, but running fsck on... (4 Replies)
Discussion started by: jj5406
4 Replies
9. AIX
Iam new to AIX
I am unable varyonvg on the vios,some of the disk are reported as harware failure.
I am going to replace the disk,Please tell me how to remove the disk without any corruption in the VG
lspv -l hdiskx also didn't work (0 Replies)
Discussion started by: roayaix
0 Replies
10. Solaris
Hi
Please can you help me on replacing or removing a faulty disk drive on a SUN NETRA X4250server with 4 internal drives only.
the format comand show me the following:
format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c0t0d0 <drive type unknown>
... (9 Replies)
Discussion started by: fretagi
9 Replies
LEARN ABOUT OSF1
volreattach
volreattach(8) System Manager's Manual volreattach(8)
NAME
volreattach - Reattaches disk drives that have once again become accessible
SYNOPSIS
/usr/sbin/volreattach [-rb] [accessname...]
/usr/sbin/volreattach -c accessname
OPTIONS
The volreattach utility has the following options: Calls the volrecover utility to attempt to recover stale plexes of any volumes on the
failed disk. Performs the reattach operation in the background. Checks whether a reattach is possible. No operation is performed, but the
name of the disk group and disk media name at which the disk can be reattached is displayed.
DESCRIPTION
The volreattach utility attempts to reattach disks using the same disk group and media names they had before detachment.
This operation may be necessary if a disk has a transient failure, or if some disk drivers are unloaded or unloadable when the Logical
Storage Manager is started, causing disks to enter the failed state.
If the problem is fixed, the volreattach command can be used to reattach the disks without plexes being flagged as stale, as long as the
reattach happens before any volumes on the disk are started.
The volreattach command is called from the voldiskadm menus as part of disk recovery.
The volreattach utility tries to find a disk with a disk group and disk ID matching that of the disk(s) being reattached. If the matching
disk is found, the reattach operation may still fail if the original cause (or some other cause) for the disk failure still exists.
EXIT CODES
A zero exit status is returned if it is possible to perform a reattach. Otherwise, non-zero is returned.
SEE ALSO
volintro(8), voldiskadm(8), volrecover(8)
volreattach(8)