04-12-2012
squid proxy: one NIC for inbound & one NIC for outbound?
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance!
9 More Discussions You Might Find Interesting
1. Solaris
can someone please through light on how to configure video and nic.
Dimension 3000 Series, Intel Pentium 4 Processor at 2.8GHz
256MB DDR SDRAM at 400MHz EA 0.00 0.00
17 in (17 in viewable) E173FP Flat Panel Display EA
Integrated Intel Extreme Graphics 2 EA
Intel Pro 100M Integrated... (4 Replies)
Discussion started by: Jimmpy
4 Replies
2. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
3. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
4. Ubuntu
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies
5. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
6. UNIX for Dummies Questions & Answers
URGENT
---------- Post updated at 04:26 AM ---------- Previous update was at 04:23 AM ----------
(I could not post I didn't know why so I need to put the contents via reply, sorry)
Hi all :D,
I am a newbie of Unix shell script and I was assigned the work from user that I need to... (3 Replies)
Discussion started by: gogkub
3 Replies
7. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
8. Shell Programming and Scripting
I have a Application Server process that hosts my application web & EJB and JMS and Database connectios etc.
Using the PID what is the best way to find out the Inbound connection sockets i.e those parties that connect to my server process on different ports numbers and Outbound connection... (2 Replies)
Discussion started by: mohtashims
2 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT MOJAVE
lwp::debug5.18
LWP::Debug(3) User Contributed Perl Documentation LWP::Debug(3)
NAME
LWP::Debug - deprecated
DESCRIPTION
LWP::Debug used to provide tracing facilities, but these are not used by LWP any more. The code in this module is kept around
(undocumented) so that 3rd party code that happen to use the old interfaces continue to run.
One useful feature that LWP::Debug provided (in an imprecise and troublesome way) was network traffic monitoring. The following section
provide some hints about recommened replacements.
Network traffic monitoring
The best way to monitor the network traffic that LWP generates is to use an external TCP monitoring program. The Wireshark program
(<http://www.wireshark.org/>) is higly recommended for this.
Another approach it to use a debugging HTTP proxy server and make LWP direct all its traffic via this one. Call "$ua->proxy" to set it up
and then just use LWP as before.
For less precise monitoring needs just setting up a few simple handlers might do. The following example sets up handlers to dump the
request and response objects that pass through LWP:
use LWP::UserAgent;
$ua = LWP::UserAgent->new;
$ua->default_header('Accept-Encoding' => scalar HTTP::Message::decodable());
$ua->add_handler("request_send", sub { shift->dump; return });
$ua->add_handler("response_done", sub { shift->dump; return });
$ua->get("http://www.example.com");
SEE ALSO
LWP::UserAgent
perl v5.18.2 2012-01-13 LWP::Debug(3)