04-12-2012
I've not heard of a "flar" image, but I think you are talking about what I remember as jumpstart, comparable to NIM on AIX and I'm sure invented everywhere else too (is it ignite on HP-UX?). That's more of an install server and in setting that up, you would include all the software to run on any (supported) hardware architecture.
I'm not that fits the bill here, but it may be possible to install from CD then ufsrestore over the top to replace all the configuration files. No guarentees, but it might work.
Be careful if you have the network card plugged in as you may end up with an IP conflict with the original server causing all sorts of trouble.
Much testing required.
I hope that this helps
Robin
Liverpool/Blackburn
UK
9 More Discussions You Might Find Interesting
1. Programming
I'm trying to use the "mknod" call in C to create a clone of /dev/null. I am stumped as to the final parameter I should provide to "mknod()". I am supposed to give it a type dev_t, which specifies a major & minor number. I want to specify major 3, minor 1, but how can I do this?
dev_t seems to... (2 Replies)
Discussion started by: nathan
2 Replies
2. Filesystems, Disks and Memory
Disk cloning
I had an external SCSI master disk that I used to clone to an identical external SCSI disk because the other SCSI disk would become corrupted. My original Master became corrupted so I used one of the other to good disk to copy back to the master. Unfortunately the new master needs... (1 Reply)
Discussion started by: stamperr
1 Replies
3. Solaris
I have a Sun T5120, and I want to programmatically determine how much RAM it has.
# uname -a
SunOS myhost 5.10 Generic_141444-09 sun4v sparc SUNW,SPARC-Enterprise-T5120
The box has 64Gb; I tried prtdiag and prtconf, but they give me bogus info
prtconf gives me:
# prtconf |grep -i... (12 Replies)
Discussion started by: thomn8r
12 Replies
4. Solaris
Trying to clone an old V240 (sun4u) onto a new T2000 (sun4v).
Managed to create a flar on the V240. Worked out that you need to add the sun4v architecture to the flar (-U "content_architecture=sun4u,sun4v" in the flarcreate).
Anyway, copied that to spare 2nd disk on my target T2000. Booted... (2 Replies)
Discussion started by: psychocandy
2 Replies
5. Solaris
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
Discussion started by: Zam_1234
3 Replies
6. Solaris
Hi!
I am quite new to Solaris and come from AIX world.
I need to clone running production LDOM. In AIX you just take mksysb and restore it to new LPAR. It will install with blank network settings.
How to do it in Solaris 11? Can't find document to clone from running system.. they talk only... (6 Replies)
Discussion started by: padapada
6 Replies
7. Solaris
Hi everyone,
We have the below sun Operating system, Now our storage team have Create a 500GB LUN for this server, How can i scan and mount the shared LUN ? Could anyone help me to resolve this issue.
SunOS my_hostname.com 5.10 Generic_150400-09 sun4v sparc sun4v
Update:
--------
I... (9 Replies)
Discussion started by: babinlonston
9 Replies
8. Solaris
Hi experts,
This is a production server.
Host information's are below
SunOS hostname_srv 5.10 Generic_150400-09 sun4v sparc sun4v
Now issue with ntp service, This host have zone in it with 9 hosts, Every hosts have ntp service issue. While i check for the service status it's in... (3 Replies)
Discussion started by: babinlonston
3 Replies
9. Red Hat
Hi
I have the following difficulty:
the NetApp admin has clone one file system from one red hatserver and presented this cloned LUN into another redhat server.
I can see the LUN as:
fdisk -l
Disk /dev/sda: 64.4 GB, 64424509440 bytes
255 heads, 63 sectors/track, 7832 cylinders
Units =... (1 Reply)
Discussion started by: fretagi
1 Replies
LEARN ABOUT DEBIAN
tinymux-install
TINYMUX-INSTALL(1) General Commands Manual TINYMUX-INSTALL(1)
NAME
tinymux-install - installer for the tinymux flavor mush server
SYNOPSIS
tinymux-install [OPTION]
DESCRIPTION
This manual page documents briefly the tinymux-install command. It was written for the Debian distribution because the original program
does not have a manual page.
tinymux-install is a program that installs the tinymux server in the user directory from which it is ran. It provides all necessary data
and configuration files for each user account it is setup for, as well as the restart script needed to initiate an instance of the tinymux
server process.
tinymux-install itself should only be run once per user to install the necessary files and links. All updating of the tinymux server should
be done on a global level by the system administrator.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
display this help and exit
-v, --version
output version information and exit
AUTHOR
This manual page was written by Ervin Hearn III <noltar@korongil.net>, for the Debian GNU/Linux system (but may be used by others).
SEE ALSO
tinymux(6)
October 25, 2004 TINYMUX-INSTALL(1)