04-11-2012
have you tried 'probe-scsi' from ok prompt?
you can choose which device boots with 'boot' command
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello!
When I use "sar -d" I get information about disk activities like:
sd0 ...
sd0,a ...
sd0,b ...
.....
sd22 ...
sd22,a ...
.....
How I can find by , for example sd22,a , what physical disk is it. For example /dev/dsk/c1t3d0s1 easy to read and I can find by it physical disk.... (4 Replies)
Discussion started by: Colf
4 Replies
2. Solaris
I've searched through unix.com and google for this issue I am having on one particular Sun E280R with installing netbackup software from CD. I know the cd is good because i installed the software on 4 other servers right before this one.
This is the issue I am seeing. vold does not mount the CD... (2 Replies)
Discussion started by: dangral
2 Replies
3. Solaris
I use the following command dk -k and get the following output:
Filesystem kbytes used avail capacity Mounted on
/dev/dsk/c0t0d0s0 1587078 56546 1482920 4% /
/dev/dsk/c0t0d0s6 1984230 926199 998505 49% /usr
/proc 0 0 0 ... (1 Reply)
Discussion started by: indianboy08
1 Replies
4. Solaris
Hi all,
I just find some strange device (at least to me) on my Sun Blade server, CP3060, like below:
bash-3.00# cd /dev/dsk
bash-3.00# ls c3*
c3t600A0B80002FA5F50000000000000000d0s0 c3t600A0B80002FA60C0000000000000000d0s4
c3t600A0B80002FA5F50000000000000000d0s1 ... (6 Replies)
Discussion started by: sleepy_11
6 Replies
5. Solaris
I have a Solaris machine running OpenSolaris v5.11.
It came with a hard drive. It's called /dev/dsk/c4d0s0.
I added two new hard drives into the box. I can't figure out what it's called in /dev/dsk. There are 210 filenames in /dev/dsk.
How do I find out which filename corresponds to the... (2 Replies)
Discussion started by: sqa777
2 Replies
6. Solaris
I installed solaris 9u8 and flar image and put on my jumpstart server which is running 10u3. Then I do jumpstart with new image with same hardware. Jumpstart acts like it installs, configures, and looks generally good. However, During the boot process, it reports the following errors.
The / file... (4 Replies)
Discussion started by: rushingfish
4 Replies
7. UNIX for Dummies Questions & Answers
Hi
May I know the meaning of the following command
mount /dev/dsk/c1t0d0s3 /mnt
Will I be able to use my tape drive after that?
Thanks (3 Replies)
Discussion started by: rahmantanko
3 Replies
8. Solaris
how to make less capacity on /dev/dsk/c1t0d0s5
Filesystem size used avail capacity Mounted on
/dev/dsk/c1t0d0s0 9.6G 2.3G 7.2G 25% /
/dev/dsk/c1t0d0s1 9.6G 4.1G 5.4G 44% /usr
/dev/dsk/c1t0d0s4 9.6G 81M 9.4G 1% /var... (1 Reply)
Discussion started by: Cah.Lanang
1 Replies
9. Solaris
Our used size is 83 gb. Total of the folders and documents size is46,2 gb. 83-46=37 gb.
Where is my space. Where was lost?
Could you please I need your opinions?
{root}/space>du -s -h *
308K alaerrm-jprof
1K argerela
20G baerckup_in
1.8G cererm
28M ecerlipselink
... (8 Replies)
Discussion started by: getrue
8 Replies
10. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)