Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
I have two 72GB disks that are mirrored and mounted (/backup). I have a 18GB drive in an array I just attached to the server, which is running Solaris 9.
I need to create a new logical volume partition and make the existing mirror device (/dev/md/dsk/d34) and the array's 18GB drive a member of... (3 Replies)
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
Hello,
First of all I must say that I have 0 solaris experience and only some average linux knowledge.
One of my friends came to ask for my help today with a Solaris 8 x86 station that would not boot.
The system is a pentium 4 1.6 ghz, 1gb ram, 40 gb hdd.
When I turn it on, I get
... (3 Replies)
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Hi,
Can you help me on booting x86 server configured under VxVM. Server boots fine normally from both the disks but if I try to boot server from mirror disk without starting veritas, then it does not boot.
vxplex -g rootdg dis var-02
vxplex -g rootdg dis swapvol-02
vxplex -g rootdg dis... (2 Replies)
Hi,
I have old server hp rp 3440 hp-ux 11.11. One mirrored disk is faulty. I need spesial patch PHKL_31216 and PHCO_30698, which give to correctly remove disk. Unfortunately I don't have access to hp support site. Please help me find it patch.
regards,Andre (0 Replies)
We have Proliant DL380 G2 running Solaris 9 x86
There are 6 physical disks installed which I believe are mirrored at hardware level to 3 sets to present 3 disks to the OS.
Is there any way to check the mirror status at OS level ?
I am guessing not and it may need a trip to site as we have no... (4 Replies)
Discussion started by: frustrated1
4 Replies
LEARN ABOUT DEBIAN
acorn-fdisk
FDISK(8) BSD System Manager's Manual FDISK(8)NAME
acorn-fdisk -- partition editor for Acorn/RISC OS machines
SYNOPSIS
acorn-fdisk -h | --help | -v | --version
acorn-fdisk [-t scheme | --type scheme] -l | --list [device ...]
acorn-fdisk [-t scheme | --type scheme] -s | --size partition
acorn-fdisk [-t scheme | --type scheme] [device]
DESCRIPTION
The acorn-fdisk utility allows one to display or interactively edit partition tables for Acorn/RISC OS machines in various formats. Using
the PC/BIOS format, standard IBM PC (i386) partition tables can also be accessed. When no optional device is given, it defaults to /dev/hda
or /dev/sda.
The options are as follows:
-h | --help Display a short usage and exit immediately.
-l | --list Display the partition table(s) of all devices.
-s | --size Display the size of partition.
-t | --type Select the partitioning scheme to use. Valid schemes are:
EESOX Eesox SCSI on the Acorn machines.
ICSIDEFS ICS IDE.
Filecore/Linux Linux on Filecore. This uses the non-ADFS descriptor to point to the start of the disc to be partitioned. The
first two sectors contain a partition table to identify the Linux partitions contained within.
PC/BIOS PC/BIOS partitioning scheme. This consists of a partition table in the first sector of the disk which contains
both CHS and LBA values for the partitions. There can be up to four entries in the primary partition table.
One of these can be an extended partition containing up to four extra partitions.
PowerTec PowerTec SCSI on the Acorn machines.
Filecore/RISCiX RiscIX on Filecore.
-v | --version
Display the version of acorn-fdisk and exit immediately.
If neither -l | --list or -s | --size are given, the partition table of the given device will be edited interactively.
EXAMPLES
Display the default device's partition table on a PC:
acorn-fdisk --type PC/BIOS -l
Display the PC partition table of /dev/sda:
acorn-fdisk --type PC/BIOS --list /dev/sda
Display the size in blocks of the partition /dev/sda1:
acorn-fdisk --type PC/BIOS --size /dev/sda1
Edit the MBR partition table interactively:
acorn-fdisk --type PC/BIOS
Display the partition table of an MBR backed up to a file:
acorn-fdisk -t PC/BIOS -l mbrdump.bin
Display the size of the first partition on a device where the MBR would be restored from the backup file mbrdump.bin:
acorn-fdisk -t PC/BIOS -s mbrdump.bin1
AUTHORS
arm-fdisk was written by Russell King <rmk@arm.uk.linux.org> based on util-linux fdisk, which was written at least partially by
A. V. Le Blanc <LeBlanc@mcc.ac.uk>.
This manual page was written for the Debian system by
Thorsten Glaser <tg@debian.org> but may be used by others.
BSD October 2, 2010 BSD