04-09-2012
Break Link Aggregation in HP UX.
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please help me.
kiron
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT DEBIAN
confdb2ldif
confdb2ldif(8) System Manager's Manual confdb2ldif(8)
NAME
confdb2ldif - Create an LDIF file from a cluster configuration
SYNOPSIS
confdb2ldap <basedn> [<config object base>]
DESCRIPTION
confdb2ldif reads the cluster configuration from the openais object database and generates an LDIF file suitable for importing into an LDAP
database. The LDIF file is written to standard output.
OPTIONS
<basedn>
This is the base DN of the LDAP server into which the configuration will be imported. confdb2ldif will create a "cn=cluster" object
below this to contain the cluster configuration. The base DN is usually derived from the host's domain name. So if the host is
ldapsrv.mycorp.com then the base DN could be dc=mycorp,dc=com.
[<config object base>]
Configuration object in the objdb to start from. This defaults to "cluster" and there should rarely be any need to change it.
COMMENTS
confdb2ldif uses the openais libconfdb to read the configuration. The default way to do this is run against a running aisexec to read the
live configuration. It is possible to generate an LDIF file from a non-running system by using the standalone feature of openais's lib-
confdb.
eg to read the configuration from /etc/cluster/cluster.conf, use the following command:
OPENAIS_DEFAULT_CONFIG_IFACE=xmlconfig:cmanpreconfig confdb2ldif dc=mycompany,dc=com
or to do it from CCS
OPENAIS_DEFAULT_CONFIG_IFACE=ccsconfig:cmanpreconfig confdb2ldif dc=mycompany,dc=com
The LDIF file is written to stdout and so can be saved or piped straight into ldapmodify if required.
It's important that the 99cluster.ldif schema file has been loaded into the LDAP server before adding the contents of this generated LDIF
file.
EXAMPLE
confdb2ldif dc=mycorp,dc=com | ldapmodify -x -a -D"cn=Directory Manager" -c -v -W
BUGS
confdb2ldif parses the cluster configuration without checking it against the loaded schema. So if there are attributes in the config file
that are not known to the schema, parts of the load will fail. It is important to check the results of feeding the output into ldapmodify.
In particular aisexec logging operations will not convert into LDIF because they rely on duplicate keys.
SEE ALSO
libconfdb(3), openais(8), cluster.conf(5)
confdb2ldif(8)