what port number is used for SSH communication and HTTPS services Post: 302616807

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Serial port communication

We're running SCO Unix Openserver 5.05 and I'm having trouble with serial communication between the com2 serial port and a handheld device. Downloading data from Unix to the handheld works perfectly, but the other way around creates a major problem. I don't know whether it's a buffer overflow or...

2. AIX

how to check status of various services and port?

How can i check which service is activated on my AIX Box? how one can check particular port is open or not (like ftp/telnet port)? I dont have admin rights

3. Programming

problem while having a communication with serial port?????

hello, I am gettin problem while sending and recieving data through seial port... when I am sending Data then the reciever end is not able to recieve that data ..... Reciever end is running in infinite loop just polling after some time to check that there is data on the port and then again...

4. IP Networking

SSH Port Forwarding - sharing the same port

Hi Linux/Unix Guru, I am setting Linux Hopping Station to another different servers. My current config to connect to another servers is using different port to connect. e.g ssh -D 1080 -p 22 username@server1.com ssh -D 1081 -p 22 username@server2.com Now what I would like to have...

5. Red Hat

Restart of services if port no is changed in /etc/services in RHEL

I had a doubt if any services need to be restarted if port no in /etc/services in an RHEL setup is changed. For eg, the port no of 443 for SSL may need to be changed. I hope my query is clear whether any services need to be restarted if port no in /etc/services is changed. Please revert with...

6. Solaris

Need suggestion:- Failed HTTPS transfer to https://supportfiles.sun.com/curl

Hi Guys, I have recently started reciving below Error message Failed HTTPS transfer to https://supportfiles.sun.com/curl whenever I run /usr/local/bin/sudo /opt/SUNWexplo/bin/explorer -P -q -v from all Servers. Looks like the SSL certificate as Expired. Whenever I type...

7. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;...

8. SuSE

Fetch port services from LDAP server

Hi, We have a ldap server configured with services (port) and want to know how to fetch that to the ldap clients: # cat /etc/nsswitch.conf|grep -i services services: files sss (neither sss nor ldap works) by doing "#getent services" I am getting only the result from /etc/services but I...

LEARN ABOUT DEBIAN

micro_proxy

micro_proxy(8)						      System Manager's Manual						    micro_proxy(8)

NAME

       micro_proxy - really small HTTP/HTTPS proxy

SYNOPSIS

       micro_proxy

DESCRIPTION

       micro_proxy  is	a  very small HTTP/HTTPS proxy.  It runs from inetd, which means its performance is poor.  But for low-traffic sites, it's
       quite adequate.	It implements all the basic features of an HTTP/HTTPS proxy, in only 260 lines of code.

       To install it, add a line like this to /etc/inetd.conf:
	   webproxy  stream tcp nowait nobody  /usr/sbin/micro_proxy micro_proxy
       Make sure the path to the executable is correct.  Then add a line like this to /etc/services:
	   webproxy   port/tcp
       Change "port" to the port number you want to use - 3128, or whatever.  Then restart inetd by sending it a "HUP" signal, or rebooting.

       On some systems, inetd has a maximum spawn rate - if you try to run inetd services faster than a certain number of  times  per  minute,	it
       assumed	there's  either  a  bug of an attack going on and it shuts down for a few minutes.  If you run into this problem - look for syslog
       messages about too-rapid looping - you'll need to find out how to increase the limit.  Unfortunately this varies from OS to OS.	 On  Free-
       BSD,  you  add  a  "-R 10000" flag to inetd's initial command line.  On some Linux systems, you can set the limit on a per-service basis in
       inetd.conf, by changing "nowait" to "nowait.10000".

AUTHOR

       Copyright (C) 1999 by Jef Poskanzer <jef@mail.acme.com>. All rights reserved.

								   16 March 1999						    micro_proxy(8)