Hi,
We recently purchased a 3 tb RAID. In the setup, it created 2 slices, one 2 tb and one 1 tb slice. Right now only the 2 tb slice is visible when booting up. I was told that the second slice needs to be mapped to a lun and a port like the first slice is.
Does anyone know how I would go... (1 Reply)
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Good day!
I’m a beginner HP-UX administrator. I have a task to create mulitipassing (I can mistake in this word) to new 3 disks which connected to my server from EVA. It is my first task to work with Secure Path. I have read what command I need to execute, but I don’t know, how to get the WWNN... (2 Replies)
Hello all,
I have the following env:
* DS4300 storage SAN
* AIX 5.3 Lpar (storage through vio server)
* AIX 5.3 Server
Some FS are too small do I'm setting up a process to increase the size of the FS.
To expand the size of the FS I plan to do the following for the physical AIX server,... (1 Reply)
Hello,
I want monting a LUN on a RX2660
I have created a LUN of 100Go with HP StorageWorks EVA and associated to my server.
For the moment I see it with the command below but after i can't used it
# ioscan -fnkC disk
Class I H/W Path Driver S/W State H/W Type Description ... (10 Replies)
Hi,
I have presented a LUN from my EVA 4400 to a RHEL server.
The server sees 4 paths to the LUN which I can see from fdisk.
If I want to add this LUN to my OS i.e.
# fdisk /dev/sd???
....which actual device do I run fdisk against?
I am running multipath so is there... (12 Replies)
Hi,
I am not getiting lun id information on VIO Server. I have used the command fget_config command.
just showing # prompt.
I would like know wheather any other command is there equiv of fget_config
which will display lun id? (4 Replies)
I have created a lun on Storage and connected it to server using fiber channel.
LUN is presented on new Server .
How do i check and mount this newly created LUN? (1 Reply)
Discussion started by: pinga123
1 Replies
10. Post Here to Contact Site Administrators and Moderators
ppmtosixel(1) General Commands Manual ppmtosixel(1)NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS -raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO ppm(5)AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)