i want to cut all the entries from the /etc/passwd file in which the uid is> 500
for this i was writing this ,m quiet new to all this.. scripting
but on the 6th n 8th line ,, i hav to specify a line number .. to get the commnd working .. but i want to use variable i instead of that ,,... (2 Replies)
Hello all.
Sorry, I know this question is similar to many others, but I just can seem to put together exactly what I need.
My file is tab delimitted and contains approximately 1 million rows. I would like to send lines 1,4,& 7 to a file. Lines 2, 5, & 8 to a second file. Lines 3, 6, & 9 to... (11 Replies)
Hello,
I am intending to perform a check based on number of "@" , present in a line in a log file . The idea is basically to perform a check on cc or bcc sender, based on an email log, which shows all the for email address. Say if the number of @ is more than 30, I will consider it as a mass... (12 Replies)
My input file:
Class
Number Position Range
1 Initial 50
1 Initial 50
2 Terminal 150
2 Terminal 20
2 Single 10
3 Single 20
4 Double 50
5 Initial 50
5 Initial 60
Class
Number... (11 Replies)
Hi Unix gurus
Basically i am searching for the pattern and getting the line numbers of the grepped pattern. I am trying to print the series of lines from 7 lines before the grepped line number to the grepped line number.
I am trying to use the following code. but it is not working.
cat... (3 Replies)
I have a file with ~200K lines, I need to delete 4K lines in it. There is no range.
I do have the line numbers of the lines which I want to be deleted.
I did tried using
> cat del.lines
sed '510d;12d;219d;......;3999d' file
> source del.lines
Word too long.
I even tried... (2 Replies)
hi Gurus,
I need separate a file which is one huge line to multiple lines based on certain number of charactors. for example:
abcdefghi high abaddffdd
I want to separate the line to multiple lines for every 4 charactors.
the result should be
abcd
efgh
i hi
gh a
badd
ffdd
Thanks in... (5 Replies)
Hi I have a file with over a million lines (rows) and I want to split everything from 500,000 to a million into another file (to make the file smaller). Is there a simple command for this?
Thank you
Phil (4 Replies)
Hi
i have requirement like below
M <form_name> sdasadasdMklkM
D ......
D .....
M form_name> sdasadasdMklkM
D ......
D .....
D ......
D .....
M form_name> sdasadasdMklkM
D ......
M form_name> sdasadasdMklkM
i want split file based on line number by finding... (10 Replies)
Hi,
Need to sort file based on the number of delimeters in the lines.
cat testfile
/home/oracle/testdb
/home
/home/oracle/testdb/newdb
/home/oracle
Here delimeter is "/"
expected Output:
/home/oracle/testdb/newdb
/home/oracle/testdb
/home/oracle
/home (3 Replies)
Discussion started by: Sumanthsv
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)