I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
I changed the tty setting for check3 in:
to /dev/ttyr014
Then I get:
Then when I test a print
It still prints to the /dev/ttyr002 printer. What am I missing?
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Any help much appreciated. I am a Java developer, not a Solaris adept. I'm having an issue reopening serial port with the Java app I am developing.
I develop in Windows and deploy the app on Solaris 10 (Sunfire X4170 with Xeon.) On the target machine my app uses the two serial ports... (11 Replies)
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT OSF1
port_names
ports(7) Miscellaneous Information Manual ports(7)NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)