hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Hello!
I am working on an application which reads environmental instruments which have serial ports. The application requires a serial port to be present to talk to the device (i.e. /dev/ttyS0 ). In some instances the environmental devices will be 100's of yards away from the computer, so a... (5 Replies)
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Any help much appreciated. I am a Java developer, not a Solaris adept. I'm having an issue reopening serial port with the Java app I am developing.
I develop in Windows and deploy the app on Solaris 10 (Sunfire X4170 with Xeon.) On the target machine my app uses the two serial ports... (11 Replies)
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT OPENSOLARIS
disable
enable(1) User Commands enable(1)NAME
enable, disable - enable/disable LP printers
SYNOPSIS
/usr/bin/enable printer...
/usr/bin/disable [-c | -W] [-r [reason]] printer...
DESCRIPTION
The enable command activates printers, enabling them to print requests submitted by the lp command. enable must be run on the printer
server.
The disable command deactivates printers, disabling them from printing requests submitted by the lp command. By default, any requests that
are currently printing on printer are reprinted in their entirety either on printer or another member of the same class of printers. The
disable command must be run on the print server.
Use lpstat -p to check the status of printers.
Generally, enable and disable are run on the print server to control local print queues. Under some configurations, they can also be run on
client systems when IPP is being used to communicate between client and server.
OPTIONS
The following options are supported for use with disable:
-c Cancels any requests that are currently printing on printer. This option cannot be used with the -W option. If the printer
is remote, the -c option is silently ignored.
-W Waits until the request currently being printed is finished before disabling printer. This option cannot be used with the -c
option. If the printer is remote, the -W option is silently ignored.
-r [reason] Assigns a reason for the disabling of the printer(s). This reason applies to all printers specified. This reason is reported
by lpstat -p. Enclose reason in quotes if it contains blanks. The default reason is unknown reason for the existing printer,
and "new printer" for a printer added to the system but not yet enabled.
OPERANDS
The following operand is supported for both enable and disable:
printer The name of the printer to be enabled or disabled. Specify printer using atomic or URI-style (scheme://endpoint) names. See
printers.conf(4) regarding the naming conventions for destinations.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
non-zero An error occurred.
FILES
/etc/printers.conf System printer configuration database
$HOME/.printers User-configurable printer database
ou=printers LDAP version of /etc/printers.conf
printers.conf.byname NIS version of /etc/printers.conf
printers.org_dir NIS+ version of /etc/printers.conf
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWlp-cmds |
+-----------------------------+-----------------------------+
|Interface Stability |Obsolete |
+-----------------------------+-----------------------------+
|CSI |Enabled |
+-----------------------------+-----------------------------+
SEE ALSO lp(1), lpstat(1), printers.conf(4), attributes(5)NOTES
When IPP is in use, the user is prompted for a passphsrase if the remote print service is configured to require authentication.
SunOS 5.11 5 Jun 2006 enable(1)