Hi,
I define 2 new LV on the vio server and run a cfgmgr on the partition and see my 2 new hdisk (hdisk6 and hdisk7).
I extend my vg vg000 (on the partition) and add the 2 hdisks.
I had a filesystem on the vg000 and when I added the disk I would like to increase the filesystem. But I cannot do a... (0 Replies)
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Hi
In my vio server I have the below output
$ lsvopt | grep -i SAPSITGS
sapsitgs_cdrom TL12UP.iso 3182
In my vio client lpar I have the below output
root@sapsitgs:/ # lsdev -Cc cdromcd0 Available Virtual SCSI Optical Served by VIO Server
cd1... (1 Reply)
Discussion started by: newtoaixos
1 Replies
LEARN ABOUT NETBSD
ahd
AHD(4) BSD Kernel Interfaces Manual AHD(4)NAME
ahd -- Adaptec PCI/PCI-X Ultra320 SCSI host adapter driver
SYNOPSIS
For one or more PCI/PCI-X cards:
ahd* at pci? dev ? function ?
To compile in debugging code:
options AHD_DEBUG
options AHD_DEBUG_OPTS=<bitmask of options>
options AHD_REG_PRETTY_PRINT
For SCSI busses:
scsibus* at ahd?
DESCRIPTION
This driver provides access to the SCSI bus(ses) connected to Adaptec AIC79xx host adapter chips.
Driver features include support for narrow and wide busses, fast, ultra, ultra2, ultra160, and ultra320 synchronous transfers, packetized
transfers, tagged queueing, and 512 SCBs.
The AHD_DEBUG_OPTS option is used to control which diagnostic messages are printed to the console when AHD_DEBUG is enabled. Logically OR
the following bits together:
Value Function
0x0001 Show miscellaneous information
0x0002 Show sense data
0x0004 Show Serial EEPROM contents
0x0008 Show bus termination settings
0x0010 Show host memory usage
0x0020 Show SCSI protocol messages
0x0040 Show mode pointer of the chip register window
0x0080 Show selection timeouts
0x0100 Show FIFO usage messages
0x0200 Show Queue Full status
0x0400 Show SCB queue status
0x0800 Show inbound packet information
0x1000 Show S/G list information
0x2000 Enable extra diagnostic code in the firmware
The AHD_REG_PRETTY_PRINT option compiles in support for human-readable bit definitions for each register that is printed by the debugging
code. However, it also bloats the compiled size of the driver by approximately 215KB.
HARDWARE
The ahd driver supports the following:
o Adaptec AIC7901 host adapter chip
o Adaptec AIC7901A host adapter chip
o Adaptec AIC7902 host adapter chip
o Adaptec 29320 host adapter
o Adaptec 39320 host adapter
o Many motherboards with on-board SCSI support
SEE ALSO ahc(4), cd(4), ch(4), intro(4), scsi(4), sd(4), ses(4), st(4)HISTORY
The ahd driver first appeared in FreeBSD 4.7 and NetBSD 2.0.
AUTHORS
The ahd driver, the AIC7xxx sequencer-code assembler, and the firmware running on the aic79xx chips was written by Justin T. Gibbs. NetBSD
porting is done by Pascal Renauld, Frank van der Linden, Jason Thorpe, and Allen Briggs. This manual page is based on the ahc(4) manual
page.
BSD May 16, 2009 BSD