interface collisions on ethernet nic Post: 302609385

10 More Discussions You Might Find Interesting

1. Programming

determine if a ethernet interface is up

Howto check if a ethernet interface is up? It's impossible to determine via the ipaddress i have learned, or? Can someone please give me a hint on howto do? Environment == Linux x86 GNU GCC. :D regards Esaia

2. AIX

PCI Ethernet NIC's for IBM RISC 600 Model B50

I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?.

3. Solaris

Sun Solaris ethernet interface

Hi, During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured, what is way to find out how many ethernet interfaces are there on Server,

4. Solaris

solaris 10 Interface not found:NIC

Hi Gurus Im a fresher and im working.I installed solaris 10 on my windows PC(dual boot) but im not able plumb my interface..everytime i use ifconfig command and tried different interfaces like eri0,ce0 etc but its displaying that interface not found.I know that there is some problem with...

5. Red Hat

changing ethernet NIC names?

I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE...

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

7. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS....

8. Solaris

Haed code nxge0 nic interface with full duplex & 1000mbps

Hi All I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only. Please also let me know how to do it online through command. regards

9. Linux

Issue with ethernet interface

hello, I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches. the IP address of eth0 is responding without problem to ping from equipment of its home network,...

10. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program

LEARN ABOUT MINIX

inet_type

inet_type(4)							   File Formats 						      inet_type(4)

NAME

       inet_type - default Internet protocol type

SYNOPSIS

       /etc/default/inet_type

DESCRIPTION

       The inet_type file defines the default IP protocol to use. Currently this file is only used by the ifconfig(1M) and netstat(1M) commands.

       The  inet_type  file  can  contain  a  number of <variable>=<value> lines. Currently, the only variable defined is DEFAULT_IP, which can be
       assigned a value of IP_VERSION4, IP_VERSION6, or BOTH.

       The output displayed by the ifconfig and netstat commands can be controlled by the value of DEFAULT_IP set in inet_type file.  By  default,
       both commands display the IPv4 and IPv6 information available on the system. The user can choose to suppress display of IPv6 information by
       setting the value of DEFAULT_IP.  The following shows the possible values for DEFAULT_IP and the resulting ifconfig and netstat output that
       will be displayed:

       IP_VERSION4     Displays only IPv4 related information. The output displayed is backward compatible with older versions of the ifconfig(1M)
		       and netstat(1M) commands.

       IP_VERSION6     Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       BOTH	       Displays both IPv4 and IPv6 related information for ifconfig and netstat.

       The command-line options to the ifconfig and netstat commands override the effect of DEFAULT_IP as set in the inet_type file. For  example,
       even if the value of DEFAULT_IP is IP_VERSION4, the command

       example% ifconfig -a6

       will display all IPv6 interfaces.

EXAMPLES

       Example 1: Suppressing IPv6 Related Output

       This is what the inet_type file must contain if you want to suppress IPv6 related output:

       DEFAULT_IP=IP_VERSION4

SEE ALSO

       ifconfig(1M), netstat(1M)

SunOS 5.10							    16 Jun 1999 						      inet_type(4)

10 More Discussions You Might Find Interesting

1. Programming

determine if a ethernet interface is up

Discussion started by: Esaia

2. AIX

PCI Ethernet NIC's for IBM RISC 600 Model B50

Discussion started by: rahe

3. Solaris

Sun Solaris ethernet interface

Discussion started by: manoj.solaris

4. Solaris

solaris 10 Interface not found:NIC

Discussion started by: madanmeer