03-19-2012
entstat -d entX or netstat -D
don't forget about man pages. man netstat
Last edited by frank_rizzo; 03-19-2012 at 09:12 PM..
Reason: add comment
This User Gave Thanks to frank_rizzo For This Post:
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
3. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
4. Solaris
Hi Gurus
Im a fresher and im working.I installed solaris 10 on my windows PC(dual boot) but im not able plumb my interface..everytime i use ifconfig command and tried different interfaces like eri0,ce0 etc but its displaying that interface not found.I know that there is some problem with... (15 Replies)
Discussion started by: madanmeer
15 Replies
5. Red Hat
I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
9. Linux
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Discussion started by: cerco
25 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT DEBIAN
networks
NETWORKS(5) Linux System Administration NETWORKS(5)
NAME
networks - network name information
DESCRIPTION
The file /etc/networks is a plain ASCII file that describes known DARPA networks and symbolic names for these networks. Each line repre-
sents a network and has the following structure:
name number aliases ...
where the fields are delimited by spaces or tabs. Empty lines are ignored. The hash character (#) indicates the start of a comment: this
character, and the remaining characters up to the end of the current line, are ignored by library functions that process the file.
The field descriptions are:
name The symbolic name for the network. Network names can contain any printable characters execept white-space characters or the comment
character.
number The official number for this network in numbers-and-dots notation (see inet(3)). The trailing ".0" (for the host component of the
network address) may be omitted.
aliases
Optional aliases for the network.
This file is read by the route(8) and netstat(8) utilities. Only Class A, B or C networks are supported, partitioned networks (i.e., net-
work/26 or network/28) are not supported by this facility.
FILES
/etc/networks
The networks definition file.
SEE ALSO
getnetbyaddr(3), getnetbyname(3), getnetent(3), netstat(8), route(8)
COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
GNU
/Linux 2008-09-04 NETWORKS(5)