03-19-2012
entstat -d entX or netstat -D
don't forget about man pages. man netstat
Last edited by frank_rizzo; 03-19-2012 at 09:12 PM..
Reason: add comment
This User Gave Thanks to frank_rizzo For This Post:
10 More Discussions You Might Find Interesting
1. Programming
Howto check if a ethernet interface is up?
It's impossible to determine via the ipaddress i have learned, or?
Can someone please give me a hint on howto do?
Environment == Linux x86 GNU GCC.
:D
regards
Esaia (2 Replies)
Discussion started by: Esaia
2 Replies
2. AIX
I am trying to locate a non IBM PCI Ethernet card that will work with the Model B50 RISC box. Alternatively, I need to find AIX drivers for standard PCI Ethernet NIC's ?. (0 Replies)
Discussion started by: rahe
0 Replies
3. Solaris
Hi,
During the installation of solaris suppose I am configuring one ethernet interface that is primary but on my server there are 4 ethernet interfaces,because all other interface not configured,
what is way to find out how many ethernet interfaces are there on Server, (6 Replies)
Discussion started by: manoj.solaris
6 Replies
4. Solaris
Hi Gurus
Im a fresher and im working.I installed solaris 10 on my windows PC(dual boot) but im not able plumb my interface..everytime i use ifconfig command and tried different interfaces like eri0,ce0 etc but its displaying that interface not found.I know that there is some problem with... (15 Replies)
Discussion started by: madanmeer
15 Replies
5. Red Hat
I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
9. Linux
hello,
I have a Linux server with two interfaces eth0 and eth1. I configured two IP addresses from two different networks on 2 interfaces, and I connected both interfaces on two different switches.
the IP address of eth0 is responding without problem to ping from equipment of its home network,... (25 Replies)
Discussion started by: cerco
25 Replies
10. UNIX for Advanced & Expert Users
Hi ,
Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
LEARN ABOUT LINUX
networks
NETWORKS(5) Linux System Administration NETWORKS(5)
NAME
networks - network name information
DESCRIPTION
The file /etc/networks is a plain ASCII file that describes known DARPA networks and symbolic names for these networks. Each line repre-
sents a network and has the following structure:
name number aliases ...
where the fields are delimited by spaces or tabs. Empty lines are ignored. If a line contains a hash mark (#), the hash mark and the
remaining part of the line are ignored.
The field descriptions are:
name The symbolic name for the network.
number The official number for this network in dotted-decimal notation. The trailing ".0" may be omitted.
aliases
Optional aliases for the network.
This file is read by route or netstat utilities. Only Class A, B or C networks are supported, partitioned networks (i.e. network/26 or
network/28) are not supported by this facility.
FILES
/etc/networks
The networks definition file.
SEE ALSO
getnetbyaddr(3), getnetbyname(3), getnetent(3), route(8), netstat(8)
COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
GNU
/Linux 2001-12-22 NETWORKS(5)