I am very new to shell scripting, and started writing a script today. I am trying to read a server name from a list that stores server name and passing each server name to get the uptime. What i would to achieve is that, i should get a file with server names along with their uptimes on a separate line.
For example:
Code:
Server1 Uptime
server2 Uptime
..and so on
My script:
Code:
server_list=`/tmp/hosts.list`
for server in $server_list
do
while read line
do
cut -f1 -d" " //hosts.list has other info like IP address
upt=`/usr/local/bin/ssh $server uptime`
printf $server $upt
done<$server
done
when i run the script i get the following error:
Code:
/tmp/hosts.list[1] : server1: not found
/tmp/hosts.list[2] : server2: not found
...and so on
Any help is greatly appreciated!
Moderator's Comments:
Please use code tags when posting data and code samples, thank you.
Last edited by Franklin52; 03-14-2012 at 05:26 PM..
Reason: Please use code tags for data and code samples, thank you
I have created a script "myscript.sh"
I need to run this script with diffrent parameters.
The parameters are stored in a file myparam.txt.
I need to run myscript.sh script for every parameter supplied in myparam.txt.
Example:
If myparam.txt contains following lines:
param1
param2
param3... (3 Replies)
I am trying to right a function which uses a file descriptor to write to a log file. The problem is that the on the print statement the file descriptor is called bad. Now when I first open the file and print to it in the f_open function by passing the descriptor to f_print_log all works well,... (6 Replies)
hi
I have a shell script say primary.sh . There is a file called params
my scenario is
primary.sh should read all the values and echo it
for example
i should pass like
$primary.sh params
output would be
Abc
... (2 Replies)
Hi All,
I have written a shell script and the script is working fine, I am passing my MIT_ID(NUMBER VALUE) to the shell script from the command prompt and my script is executing as expected.
Now I have to pass all the MIT_ID's from a .txt file to the shell script,as I am automating this I... (6 Replies)
I have an for loop that reads the following file
cat param.cfg
val1:env1:opt1
val2:env2:opt2
val3:env3:opt3
val4:env4:opt4
.
.
The for loop extracts the each line of the file so that at any one point, the value of i is
val1:env1:opt1 etc...
I would like to extract each... (19 Replies)
Hi
Im trying to run zip shell command from an Oracle job, but this has limitations.
This should take a few of explanaition,..
Oracle allows me to execute a command and then I can set up a fixed number of arguments. Ex: (summarizing in something like..):
JOB DEFINITION
job_name: test... (4 Replies)
Hi ,
I am passing date parameter through file
my shell script testing.sh is
#set -x
#set -v
asd=$1
asd1=$2
echo $asd
echo $asd1
Passing parameter as below
sh testing.sh `cat file1.txt`
Output (2 Replies)
Hello Everyone,
I have developed a shell script which takes schema id and password as parameter to login into database using sqlplus,runs a query and mails the result.
My requirement is that, I dont want to pass userid and password as parameters.Instead,I want to pass say Environment... (4 Replies)
Below is the command
mv AP_FLEXCUBE_INTERFACE10.txt FTPYMNTE_`date "+%Y%m%d%H%M%S" | tr '' ''`.TXT
it is changing the file name to a different name according to time stamp dynamically. I want to capture that dynamic file name present in the directory to a variable .
After that i want to... (6 Replies)
Discussion started by: sujit das
6 Replies
LEARN ABOUT MINIX
sftp-server
sftp-server(1M) System Administration Commands sftp-server(1M)NAME
sftp-server - SFTP server subsystem
SYNOPSIS
/usr/lib/ssh/sftp-server
DESCRIPTION
sftp-server implements the server side of the SSH File Transfer Protocol as defined in the IETF draft-ietf-secsh-filexfer.
sftp-server is a subsystem for sshd(1M) and must not be run directly. There are no options or config settings.
To enable the sftp-server subsystem for sshd add the following to /etc/ssh/sshd_config:
Subsystem sftp /usr/lib/ssh/sftp-server
See sshd_config(4) for a description of the format and contents of that file.
There is no relationship between the protocol used by sftp-server and the FTP protocol (RFC 959) provided by in.ftpd.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
FILES
/usr/lib/sftp-server
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsshdu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO sftp(1), ssh(1), ssh-add(1), ssh-keygen(1), sshd(1M), sshd_config(4), attributes(5)
To view license terms, attribution, and copyright for OpenSSH, the default path is /var/sadm/pkg/SUNWsshdr/install/copyright. If the
Solaris operating environment has been installed anywhere other than the default, modify the given path to access the file at the installed
location.
AUTHOR
Markus Friedl
SunOS 5.10 30 Jul 2003 sftp-server(1M)
03-14-2012
