IP Bonding Post: 302605992

10 More Discussions You Might Find Interesting

1. IP Networking

Bonding Internet Connections

I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster...

2. IP Networking

Bonding of IP tunnels

Hello. Our Company is spreaded over Germany. There are main offices an branch offices. These offices are mostly connecte via multiple sdsl. We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances. It seemed that only one VPN Connetion between to offices could be...

3. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

4. Red Hat

RHEL 5.5 NIC Bonding

I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch. The problem is dropped packets and eth03 wont come up in the PO...

5. Red Hat

Bonding a Bond with LACP

Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would...

6. Red Hat

BONDING with Flapping issue!

Hi team, I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes,...

7. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB...

8. Red Hat

How to change bonding configuration in Linux 5.9?

I have 2 ethernet port in my linux (Red hat 5.9) machine.The 2 ethernet ports (eth0 and eth1)are bonded and are making one single ethernet port namely bond0. I have adaptive load share option selected.Now in this condition, if my eth0 port disconnected due to some failure, then will eth1 take the...

9. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are...

10. Red Hat

Network bonding

Dear All , Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x. After configuring , we restarted the network services , the link was down after that , we could not login in to the Server. So after that , we logged in to console and tried to...

LEARN ABOUT SUSE

ifcfg-bonding

IFCFG-BONDING(5)					       Network configuration						  IFCFG-BONDING(5)

NAME

       ifcfg-bonding - interface bonding configuration

SYNOPSIS

       /etc/sysconfig/network/ifcfg-bond*

Bonding Interfaces
       To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
       ables

       BONDING_MASTER
	      must be set to 'yes' to identify this interface as a bonding interface

       BONDING_SLAVE_<X>
	      here you specify the interface name representing the slave network interfaces.

       BONDING_MODULE_OPTS
	      contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for	backup	mode).	For  addi-
	      tional information take a look into the documentation mentioned at the bottom.  Note, that this options are not passed as parameters
	      to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.

       BONDING_SKIP_REMOVE_WORKAROUND
	      When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party  ker-
	      nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
	      bonding interface causing all network related operation to stuck.

	      Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old  options
	      and set them to their default setting on bonding configuration changes or to reboot.

Example
       Example for a bonding interface on eth0 and eth1 using the backup mode

       ifcfg-bond0
	  STARTMODE='onboot'
	  BOOTPROTO='static'
	  IPADDR='192.168.0.1/24'

	  BONDING_MASTER='yes'
	  BONDING_SLAVE_0='eth0'
	  BONDING_SLAVE_1='eth1'
	  BONDING_MODULE_OPTS='mode=active-backup miimon=100'

Additional Information
       For  additional	and  more  general  information  take  a look into /usr/src/linux/Documentation/networking/bonding.txt.  Maybe you need to
       install the kernel sources to get this additional documentation.

       The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.

BUGS

       Please report bugs at <http://www.suse.de/feedback>

AUTHOR

       Christian Zoz <zoz@suse.de> -- ifup script
       Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page

SEE ALSO

       ifcfg(5), ifup(8).

sysconfig							    April 2005							  IFCFG-BONDING(5)