03-08-2012
breaking into a v240's alom
had a v240 pre-configured and running the OS and alom, for about 3 months good, no issues.
All of sudden, I can't see the IP address of the OS and the alom..
There is nothing wrong with thet network...
I suspect the ALOM crashed and/or something bad happened to it..
Is there anyway to break into it ??
I imagined if the ALOM did not come up, neither the OS would ..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello all,
Does anyone know how to reset the ALOM password for Sun fire V240 or the OBP password? I was given a V240 without any password or hard drive.
Thanks (3 Replies)
Discussion started by: larryase
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I trying to jumpstart SunFire V240 Solaris 10, 2006_01. All the jumpstart files on jumpstart install and boot server are ok (tested on another machine Sun Ultra 10). But this system comes out with: "The file just loaded does not appear to be executable." after "boot net - install" and setting... (0 Replies)
Discussion started by: jump
0 Replies
3. Solaris
Hi,
we are having one sun v240 server, now this server is performing very slow,
checked using top, iostat and vmstat commands, output is looking normal, but the performance is very slow and generating more traffic in network,
how can we resolve this.
Regards
RJS (5 Replies)
Discussion started by: rajasekg
5 Replies
4. Hardware
I recently acquired a sunfire v240 and I'm trying to get into it so I can install linux on it. Right now I'm still trying to get a monitor connected so I can do this.
I've tried connecting to it with a crossover cable to my laptop (vista and linux equipped). I was able to get a connection... (2 Replies)
Discussion started by: QuadRunner750
2 Replies
5. Solaris
hallo anybody know how to set alom mail alerty server with yahoomail ?
thank u?where i can find mail server address for yahoomail?thank (1 Reply)
Discussion started by: yanto85
1 Replies
6. Solaris
Dear All,
I have problem with SF V240 with solaris 10. This server always booting with error message like this
What's problem with my server?
Best Regards
Wisnu:) (10 Replies)
Discussion started by: mbah_jiman
10 Replies
7. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
8. Solaris
after shutting down the server and the ILOM/ALOM,
its date seems to go back to 1977..rather than current date..
problem with battery on ILOM/ALOM ??:( (1 Reply)
Discussion started by: ppchu99
1 Replies
9. Solaris
Hey guys,
I recently replaced the heatsinks on two different V240's. Repasted and replaced them myself. After attempting to bring them back up, there was no display coming from the KVM. I figured it was a matter of environment in OBP and attempted to get to the OK prompt from the... (20 Replies)
Discussion started by: DanielSluder
20 Replies
10. Solaris
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
LO(4) BSD Kernel Interfaces Manual LO(4)
NAME
lo -- software loopback network interface
SYNOPSIS
pseudo-device
loop
DESCRIPTION
The loop interface is a software loopback mechanism which may be used for performance analysis, software testing, and/or local communication.
As with other network interfaces, the loopback interface must have network addresses assigned for each address family with which it is to be
used. These addresses may be set or changed with the SIOCSIFADDR ioctl(2). The loopback interface should be the last interface configured,
as protocols may use the order of configuration as an indication of priority. The loopback should never be configured first unless no hard-
ware interfaces exist.
DIAGNOSTICS
lo%d: can't handle af%d. The interface was handed a message with addresses formatted in an unsuitable address family; the packet was
dropped.
SEE ALSO
inet(4), intro(4), ns(4)
HISTORY
The lo device appeared in 4.2BSD.
BUGS
Previous versions of the system enabled the loopback interface automatically, using a nonstandard Internet address (127.1). Use of that
address is now discouraged; a reserved host address for the local network should be used instead.
4.2 Berkeley Distribution June 5, 1993 4.2 Berkeley Distribution