Sponsored Content
Operating Systems Linux Red Hat Static IP Address setup for vm as well as the host system Post 302604039 by mark54g on Friday 2nd of March 2012 03:58:29 PM
Old 03-02-2012
Oracle is not supported on Virtual Box, and it may not work properly, but you can sure try.

If you would like them to all be on the same subnet, then you need to make sure that you set your ethernet adapter (possibly eth0, or some other adapter you have configured) to bridged mode.

Then you can configure the IP addresses to exist as if it were a real machine.

I would suggest you change the driver type in the advanced tab from the Desktop Gigabit adapter to the T or MT server adapter type of intel gigabit emulation.

I would also make sure to use a better chipset driver and emulate a SAS controller for the disks, rather than SATA controller.


Also make sure that your system's BIOS is configured for intel virtualization extensions.

That being said, you should probably not run them all simultaneously or it will be entirely too slow. You are likely looking at the tests for this running significantly slower than you expect. I would suggest you try faster spinning drives, or SSD for your tests.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Slow from static IP ... fast from NAT address

Has anyone had an issue where: If I telnet into a unix machine on my network, from within my natted address, there is no speed issue. When I telnet to the same machine using the static address, it is very very slow. This SCO 5.06. There is no nameserver running. Please help. I have... (3 Replies)
Discussion started by: gseyforth
3 Replies

2. Solaris

Add Static Routes to new physical address

Hi, I need help to add new route: 10.252.0.138, GW 10.252.0.129 to e1000g1 and 10.252.0.10, GW 10.252.0.1 to e1000g2 tnx (4 Replies)
Discussion started by: mehrdad68
4 Replies

3. UNIX for Dummies Questions & Answers

How to apply static ip address

Hi there, I have a Debian 5.0 server newly installed. By default, the ip address is given by dhcp. pegase:~# grep '^' /etc/network/interfaces auto lo iface lo inet loopback allow-hotplug eth0 iface eth0 inet dhcp pegase:~# head -2 /etc/hosts 127.0.0.1 localhost 127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies

4. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies

5. UNIX for Dummies Questions & Answers

Static IP address for solaris 10 virtual machine

Hi All I am having a solaris 10 virtual machine on vista (using vmware 7) laptop. Now i want to access virtual machine from vista using putty. Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies

6. UNIX for Dummies Questions & Answers

Static IP address works on Ethernet but not Wireless

Hi all, I have literally spent all day trying dozens of different combinations, re-installs and tweaks to try and resolve this problem. I would be EXTREMELY grateful if anyone can help/point me in the right direction. I am using OpenBSD 4.6 and am trying to connect to my wireless network with... (1 Reply)
Discussion started by: wcontm
1 Replies

7. Red Hat

Purpose of Static IP address through DHCP

Hi All, Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies

8. IP Networking

Free subdomain to my IP Address and Static IP

Hi all, I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service? Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies

9. IP Networking

Configuring static ip address on several systems

p { margin-bottom: 0.1in; line-height: 120%; }a:link { } Hello, I'm have an interesting issue with some Raspberry Pi's which I have on my home network. The pi's are on 192.168.1.102, 192.168.1.103, 192.168.1.104 Something very strange is happening on my network. The pi on 192.168.1.104 is... (2 Replies)
Discussion started by: JoeOnaMac
2 Replies

10. Linux

Unable to set static ip address

Hi All, Am using centos 7 in my vmware workstatio with the bridged network. when run the ifconfig cmd its not at all showing the ip address and pls advise how to set static ip address in my linux box. (1 Reply)
Discussion started by: sarathkumar s
1 Replies
Apache::Session::Store::Oracle(3pm)			User Contributed Perl Documentation		       Apache::Session::Store::Oracle(3pm)

NAME
Apache::Session::Store::Oracle - Store persistent data in a Oracle database SYNOPSIS
use Apache::Session::Store::Oracle; my $store = new Apache::Session::Store::Oracle; $store->insert($ref); $store->update($ref); $store->materialize($ref); $store->remove($ref); DESCRIPTION
Apache::Session::Store::Oracle fulfills the storage interface of Apache::Session. Session data is stored in a Oracle database. SCHEMA
To use this module, you will need at least these columns in a table called 'sessions': id varchar2(32) # or however long your session IDs are. a_session long To create this schema, you can execute this command using the sqlplus program: CREATE TABLE sessions ( id varchar2(32) not null primary key, a_session long ); If you use some other command, ensure that there is a unique index on the table's id column. CONFIGURATION
The module must know what datasource, username, and password to use when connecting to the database. These values can be set using the options hash (see Apache::Session documentation). The options are DataSource, UserName, and Password. Example: tie %hash, 'Apache::Session::Oracle', $id, { DataSource => 'dbi:Oracle:database', UserName => 'database_user', Password => 'K00l' }; Instead, you may pass in an already-opened DBI handle to your database. tie %hash, 'Apache::Session::Oracle', $id, { Handle => $dbh }; The last option is LongReadLen, which specifies the maximum size of the session object. If not supplied, the default maximum size is 8 KB. AUTHOR
This modules was written by Jeffrey William Baker <jwbaker@acm.org> A fix for the commit policy was contributed by Michael Schout <mschout@gkg.net> SEE ALSO
Apache::Session, Apache::Session::Store::DBI perl v5.10.1 2010-10-18 Apache::Session::Store::Oracle(3pm)
All times are GMT -4. The time now is 03:54 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy