03-02-2012
Oracle is not supported on Virtual Box, and it may not work properly, but you can sure try.
If you would like them to all be on the same subnet, then you need to make sure that you set your ethernet adapter (possibly eth0, or some other adapter you have configured) to bridged mode.
Then you can configure the IP addresses to exist as if it were a real machine.
I would suggest you change the driver type in the advanced tab from the Desktop Gigabit adapter to the T or MT server adapter type of intel gigabit emulation.
I would also make sure to use a better chipset driver and emulate a SAS controller for the disks, rather than SATA controller.
Also make sure that your system's BIOS is configured for intel virtualization extensions.
That being said, you should probably not run them all simultaneously or it will be entirely too slow. You are likely looking at the tests for this running significantly slower than you expect. I would suggest you try faster spinning drives, or SSD for your tests.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Has anyone had an issue where:
If I telnet into a unix machine on my network, from within my natted address,
there is no speed issue.
When I telnet to the same machine using the static address, it is very very
slow.
This SCO 5.06. There is no nameserver running.
Please help. I have... (3 Replies)
Discussion started by: gseyforth
3 Replies
2. Solaris
Hi,
I need help to add new route:
10.252.0.138, GW 10.252.0.129 to e1000g1
and
10.252.0.10, GW 10.252.0.1 to e1000g2
tnx (4 Replies)
Discussion started by: mehrdad68
4 Replies
3. UNIX for Dummies Questions & Answers
Hi there,
I have a Debian 5.0 server newly installed.
By default, the ip address is given by dhcp.
pegase:~# grep '^' /etc/network/interfaces
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
pegase:~# head -2 /etc/hosts
127.0.0.1 localhost
127.0.1.1 ... (1 Reply)
Discussion started by: chebarbudo
1 Replies
4. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
5. UNIX for Dummies Questions & Answers
Hi All
I am having a solaris 10 virtual machine on vista (using vmware 7) laptop.
Now i want to access virtual machine from vista using putty.
Problem is that i insalled the solaris machine as dhcp. and whenever i connect to internet or reboot my system the IP address of solaris... (1 Reply)
Discussion started by: ankurk
1 Replies
6. UNIX for Dummies Questions & Answers
Hi all,
I have literally spent all day trying dozens of different combinations, re-installs and tweaks to try and resolve this problem. I would be EXTREMELY grateful if anyone can help/point me in the right direction.
I am using OpenBSD 4.6 and am trying to connect to my wireless network with... (1 Reply)
Discussion started by: wcontm
1 Replies
7. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
8. IP Networking
Hi all,
I would need to register a random free subdomain address and associate that to my IP Address. Any suggestion of a good service?
Also I don't have a static IP but i remember that there are services that automatically reset the right IP address behind the subdomain but i don't remember... (1 Reply)
Discussion started by: Tameto
1 Replies
9. IP Networking
p { margin-bottom: 0.1in; line-height: 120%; }a:link { } Hello,
I'm have an interesting issue with some Raspberry Pi's which I have on my home network.
The pi's are on 192.168.1.102, 192.168.1.103, 192.168.1.104
Something very strange is happening on my network. The pi on 192.168.1.104 is... (2 Replies)
Discussion started by: JoeOnaMac
2 Replies
10. Linux
Hi All,
Am using centos 7 in my vmware workstatio with the bridged network. when run the ifconfig cmd its not at all showing the ip address and pls advise how to set static ip address in my linux box. (1 Reply)
Discussion started by: sarathkumar s
1 Replies
IXGB(4) BSD Kernel Interfaces Manual IXGB(4)
NAME
ixgb -- Intel(R) PRO/10GbE Ethernet driver for the FreeBSD operating system
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ixgb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ixgb_load="YES"
DESCRIPTION
The ixgb driver provides support for PCI Gigabit Ethernet adapters based on the Intel 82597EX Ethernet controller chips. The driver supports
Transmit/Receive checksum offload and Jumbo Frames.
For questions related to hardware requirements, refer to the documentation supplied with your Intel PRO/10GbE adapter. All hardware require-
ments listed apply to use with FreeBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixgb driver supports the following cards:
o Intel PRO/10GbE LR Server Adapter
o Intel PRO/10GbE SR Server Adapter
DIAGNOSTICS
ixgb%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixgb%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixgb%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information
related to the issue to <freebsd@intel.com>.
SEE ALSO
arp(4), em(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)
HISTORY
The ixgb device driver first appeared in FreeBSD 4.11 and FreeBSD 5.3.
AUTHORS
The ixgb driver was written by Intel Corporation <freebsd@intel.com>.
BSD
August 18, 2006 BSD