03-02-2012
Through SSH. There is no serial access.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Discussion started by: jsy
1 Replies
2. Solaris
Hello Guys,
I am working with sunfire V480 and wants to know how to connect to alom. Can you please guide? (7 Replies)
Discussion started by: mokkan
7 Replies
3. Solaris
hello guys.... I'm newbie in solaris server / os, anybody know how disable alom server v240.
thank u (9 Replies)
Discussion started by: yanto85
9 Replies
4. Solaris
Hi guys,
I'm in trouble with a Sunfire T2000.
The OS (Solaris10) is up and running, but I can't log in the sc>I think the terminal server is crashed!
Does anyone know if I can reset the sc> from the OS?
How can I do that?
Thx (6 Replies)
Discussion started by: cecco16
6 Replies
5. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
6. Solaris
Hi gurus,
I have a sun netra 240 server. I want to get to the ALOM but it always ask for login and password. Can anyone tell me how I can reset the ALOM it to default so I can be able to configure it?
Thanks lots. (2 Replies)
Discussion started by: cjashu
2 Replies
7. Solaris
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Discussion started by: br1an
19 Replies
8. Solaris
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Discussion started by: rajasraf
1 Replies
9. Solaris
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
10. Hardware
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
LEARN ABOUT DEBIAN
pam_ssh
PAM_SSH(8) BSD System Manager's Manual PAM_SSH(8)
NAME
pam_ssh -- authentication and session management with SSH private keys
DESCRIPTION
The SSH authentication service module for PAM, pam_ssh provides functionality for two PAM categories: authentication and session management.
SSH Authentication Module
The SSH authentication component verifies the identity of a user by prompting the user for a passphrase and verifying that it can decrypt at
least one of the user's SSH login keys using that passphrase.
The following options may be passed to the authentication module:
debug syslog(3) debugging information at LOG_DEBUG level.
use_first_pass If the authentication module is not the first in the stack, and a previous module obtained the user's password, then
that password is used to decrypt the user's SSH login keys. If this fails, then the authentication module returns
failure without prompting the user for a passphrase.
try_first_pass Similar to the use_first_pass option, except that if the previously obtained password fails to decrypt any of the SSH
login keys, then the user is prompted for an SSH passphrase.
try_first_pass has no effect if pam_ssh is the first module on the stack, or if no previous modules obtained the
user's password.
allow_blank_passphrase Allow SSH keys with no passphrase.
If neither use_first_pass nor try_first_pass is specified, pam_ssh will unconditionally ask for an SSH passphrase.
In addition to the above authentication procedure, all standard SSH keys (identity, id_rsa, id_dsa) for which the obtained password matches
will be decrypted.
SSH Session Management Module
The SSH session management component initiates sessions by starting an SSH agent, passing it any SSH login keys it decrypted during the
authentication phase, and sets the environment variables accordingly.
The SSH session management component terminates the session by killing the previously started SSH agent by sending it a SIGTERM.
The following options may be passed to the session management module:
debug syslog(3) debugging information at LOG_DEBUG level.
INFORMATION LEAKS
Be careful with the using the try_first_pass option when pam_ssh is the first authentication module because it will then leak information
about existing users without login keys: such users will not be asked for a specific SSH passphrase, whereas non-existing users and existing
users with login keys will be asked for a passphrase.
FILES
$HOME/.ssh/identity
$HOME/.ssh/id_rsa
$HOME/.ssh/id_dsa OpenSSH DSA/RSA keys decrypted by pam_ssh.
$HOME/.ssh/login-keys.d/ Location of (possibly symbolic links to) OpenSSH DSA/RSA keys used for authentication and decrypted by pam_ssh.
/var/log/auth.log Usual log file for syslog(3)
SEE ALSO
ssh-agent(1), syslog(3), pam.conf(5), pam(8).
AUTHORS
Andrew J. Korty <ajk@iu.edu> wrote pam_ssh. Dag-Erling Smorgrav wrote the original OpenPAM support code. Mark R V Murray wrote the original
version of this manual page. Jens Peter Secher introduced the login-key concept.
BSD
November 26, 2001 BSD