03-02-2012
by which way u take Ilom logins of servers......by putty or by hyper terminal...
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Discussion started by: jsy
1 Replies
2. Solaris
Hello Guys,
I am working with sunfire V480 and wants to know how to connect to alom. Can you please guide? (7 Replies)
Discussion started by: mokkan
7 Replies
3. Solaris
hello guys.... I'm newbie in solaris server / os, anybody know how disable alom server v240.
thank u (9 Replies)
Discussion started by: yanto85
9 Replies
4. Solaris
Hi guys,
I'm in trouble with a Sunfire T2000.
The OS (Solaris10) is up and running, but I can't log in the sc>I think the terminal server is crashed!
Does anyone know if I can reset the sc> from the OS?
How can I do that?
Thx (6 Replies)
Discussion started by: cecco16
6 Replies
5. Solaris
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
Discussion started by: bobby320
0 Replies
6. Solaris
Hi gurus,
I have a sun netra 240 server. I want to get to the ALOM but it always ask for login and password. Can anyone tell me how I can reset the ALOM it to default so I can be able to configure it?
Thanks lots. (2 Replies)
Discussion started by: cjashu
2 Replies
7. Solaris
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Discussion started by: br1an
19 Replies
8. Solaris
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Discussion started by: rajasraf
1 Replies
9. Solaris
Hi,
How to set ip address on eth0 for access ssh from ALOM? Is it possible? Now i cannot access it because don't have VGA.
I keep try to access using ssh. Please guide me.
Thanks. (16 Replies)
Discussion started by: mzainal
16 Replies
10. Hardware
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
LEARN ABOUT HPUX
lcpu_attr
lcpu_attr(5) File Formats Manual lcpu_attr(5)
NAME
lcpu_attr - dynamically enable or disable LCPU attribute of the default processor set
VALUES
Fail Safe
Default
the LCPU attribute of the default processor set is disabled
Allowed values
or
DESCRIPTION
This tunable dynamically enables or disables the logical processor (LCPU) attribute in the default processor set. On systems supporting
hyper-threading technology, each hyper-thread is represented as an LCPU.
When the LCPU attribute is enabled, the processor cores in the default processor have hyper-threading enabled. If the LCPU attribute is
disabled, the physical processors in the default processor set behave as single threaded processor cores.
See pset_setattr(2) for information about managing the LCPU attribute in processor sets other than the default processor set.
Who Is Expected to Change This Tunable?
System administrators that wish to change hyper-threading ability in the default processor set.
Restrictions on Changing
The tunable has no effect on platforms that do not have hyper-threading capability or systems with hyper-threading disabled at the firmware
level. On systems that support hyper-threading, the firmware feature must be enabled to dynamically enable/disable the LCPU attribute in
the default processor set.
When Should the Tunable Be Turned On?
The tunable should be turned on to enable the LCPU attribute in the default processor set to take advantage of hyper-threading. If the
applications running on the system see performance benefits, the LCPU attribute should remain enabled.
What Are the Side Effects of Turning the Tunable On?
Some workloads may experience performance degradation when the LCPU attribute is enabled.
When Should the Tunable Be Turned Off?
Some applications may experience performance degradation or may not see any performance benefits from using hyper-threading. In this case,
this tunable should be turned off.
What Are the Side Effects of Turning the Tunable Off?
With LCPU turned off, applications may not take advantage of hyper-threading.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
SEE ALSO
psrset(1M), pset_assign(2), pset_bind(2), pset_create(2), pset_ctl(2), pset_destroy(2), privgrp(4).
Tunable Kernel Parameters lcpu_attr(5)