03-01-2012
Thank you very much for this ... quite helpful
10 More Discussions You Might Find Interesting
1. Solaris
I would like to extend a logical drive on our 3510. I have four unallocated disks which I would like to use for this purpose.
The 3510 supports a Sun Cluster but for now all I wish to see is a "new" disk when I run format.
I am a little familiar with the telnet/ssh session on the 3510 but am... (2 Replies)
Discussion started by: malcqv
2 Replies
2. AIX
Hello,
This morning we have added 6 new disks (73 Gb) to our DS4300, then created a new Array en then created a logical drive, after this was done, teh following error occourd on the last 3 (new)disks:
Date/Time: 22-4-08 6:56:26
Sequence number: 5472
Event type: 282D
Event category:... (1 Reply)
Discussion started by: topper
1 Replies
3. Filesystems, Disks and Memory
Hi people, I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to get... (1 Reply)
Discussion started by: adam466
1 Replies
4. Filesystems, Disks and Memory
Hi people,
I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to... (2 Replies)
Discussion started by: christopher4
2 Replies
5. AIX
Hi,
I was looking on Google for AIX-VIO/LPAR with ISCSI solution and found following really nice tutorial about how to setup ISCSI with free NAS.
1) Build Your Own Open Source NAS Device Using FreeNAS | Train Signal Training - Free Computer Training Videos
2) Build Your Own Open Source... (4 Replies)
Discussion started by: kabir
4 Replies
6. AIX
Hi All,
Recently I'm taking my first steps in AIX, initially with no real issues. Until now, off course...
I hooked up a couple of iSCSI disks to the system, with a RHEL5 machine running tgt on the other side. When running cfgmgr after initial configuration, I got an error:
# cfgmgr -l... (4 Replies)
Discussion started by: mr.aart
4 Replies
7. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
8. AIX
Hi
Below are the new luns added by the storage team. My cluster setup is a three node HA cluster. I could see the below mentioned luns on all the three nodes :
hdisk26 00084dd0ef986943 None
hdisk27 00084dd0ef988d1f None
and we tried to... (3 Replies)
Discussion started by: newtoaixos
3 Replies
9. Ubuntu
Does anyone know what is solution for this error ?tar: Exiting with failure status due to previous errors from last 3 days I am trying to take backup of home/user directory getting again and again same error please anyone give me solution (8 Replies)
Discussion started by: Akshay Hegde
8 Replies
10. AIX
AIX 7.1
New to WPAR, hopefully just missing something simple here.
Creating the WPAR like this.....
(The box where the WPAR is hosted does have an iscsi protocol device)
mkwpar -h wpar08 -l -n wpar08 -N interface=en0 address=xxx.xx.xx.xxx netmask=255.255.255.0 -D devname=/dev/iscsi0 -D... (0 Replies)
Discussion started by: TomR
0 Replies
LEARN ABOUT NETBSD
iscsi-target
ISCSI-TARGET(8) BSD System Manager's Manual ISCSI-TARGET(8)
NAME
iscsi-target -- service remote iSCSI requests
SYNOPSIS
iscsi-target [-46DV] [-b block length] [-f configuration file] [-p port number] [-s maximum number of sessions] [-t target name]
[-v verbose arg]
DESCRIPTION
iscsi-target is the server for iSCSI requests from iSCSI initiators. iscsi-target listens for discovery and login requests on the required
port, and responds to those requests appropriately.
Options and operands available for iscsi-target:
-4 iscsi-target will listen for IPv4 connections, and respond back using IPv4. This is the default address family.
-6 iscsi-target will listen for IPv6 connections, and respond back using IPv6.
-b blocksize
Specify the underlying block size for iSCSI storage which will be served. The possible sizes are: 512, 1024, 2048, and 4096 bytes,
with the default being 512 bytes.
-D When this option is specified, iscsi-target will not detach itself from the controlling tty, and will not become a daemon. This can
be useful for debugging purposes.
-f configfile
Use the named file as the configuration file. The default file can be found in /etc/iscsi/targets. See targets(5) for more informa-
tion.
-p port number
Use the port number provided as the argument as the port on which to listen for iSCSI service requests from initiators.
-s maximum number of sessions
Allow the maximum number of sessions to be initiated when connecting to the target.
-t filename
The target name (as it appears to the iSCSI initiator) can be specified using this flag.
-V iscsi-target will print the utility name and version number, and the address for bug reports, and then exit.
-v argument
The amount of information shown can be varied by using this command. Possible values of argument are net to show network-related
information, iscsi to show iSCSI protocol-related information, scsi to show SCSI protocol information, and all to show information
from all of the above arguments.
FILES
/etc/iscsi/targets the list of exported storage
/var/run/iscsi-target.pid the PID of the currently running iscsi-target
SEE ALSO
targets(5)
HISTORY
The iscsi-target utility first appeared in NetBSD 4.0.
BSD
May 27, 2006 BSD