02-28-2012
p520 accessing the SP
managed to get in and reset the IP addresses..
connecting the ethernet cable to both hmc1 and hmc2..
I could now ping the IP address of both hmc1 and hmc2..
but trying to go
https://ip_hmc1 or
https://ip_hmc2
is no go..on this p520..
10 More Discussions You Might Find Interesting
1. HP-UX
I am receiving messages from HP-UX Server
"The operating system is unable to communicate with the service processor.
The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ".
I need help in the following:... (1 Reply)
Discussion started by: cgege
1 Replies
2. AIX
I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this? (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
3. AIX
hello everybody.
Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please? (5 Replies)
Discussion started by: soahel
5 Replies
4. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
5. AIX
Hi Folks,
I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two... (6 Replies)
Discussion started by: shaell
6 Replies
6. AIX
I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line
The settings are correct in both sides, But I can't establish a connection.
I suspect that there's something that I should do regarding the... (3 Replies)
Discussion started by: ayman metwally
3 Replies
7. AIX
it shows up after the upgrade to SF240_415, after 2 hrs.
amber light shows up on the led of 9111-520, but alog shows:
everything seems to work, not sure what's going on.. (6 Replies)
Discussion started by: ppchu99
6 Replies
8. AIX
trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think
a few questions, on this practice AIX machine on AIX 7.1
VIO can only be installed if ASMI or HMC is running ???
if so, perhaps ASMI is much simpler, since I will need to... (2 Replies)
Discussion started by: ppchu99
2 Replies
9. AIX
picked up an old p520..and also spend sometimes to manage software:
a) AIX 7.1
b) VIOS Server 2.2
attempting to run a few LPARs without much more $$$$, as this is a home-made projects..
machine hdisk0, pre-installed with AIX 7.1
a few questions:
a) In order to run LPARs, I will... (7 Replies)
Discussion started by: ppchu99
7 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT MOJAVE
faxstate
FAXSTATE(8) System Manager's Manual FAXSTATE(8)
NAME
faxstate - control ``modem state'' of a device used by HylaFAX
SYNOPSIS
/usr/sbin/faxstate [ -q queue-dir ] [ -s state ] [ -n ] modem
DESCRIPTION
faxstate sends a message to the HylaFAX faxgetty(8) process servicing modem telling it to use the specified state when notifying the
HylaFAX scheduler that a modem is ready and available for use. This is useful for controlling outbound use of a modem; by marking a
modem's state as busy or down the HylaFAX scheduler will not assign any outbound jobs to the modem.
The specified modem can either be the name (typically the last component of the terminal port the modem is attached to), or the full name
of the associated FIFO named pipe file, e.g. ``FIFO.ttym2''.
If the -n option, faxstate emulates what faxgetty would do; sending a message directly to the faxq process marking the specified modem
down, busy, or ready. This interface is useful for send-only environments in which faxgetty processes are not used. Note that modems
manipulated in this way must previously have been configured with the faxmodem(8) program.
OPTIONS
The following options are supported:
-n Contact faxq directly instead of faxgetty.
-q dir Use a spooling area other than /var/spool/hylafax.
-s Specify the state to send the faxq process each time the modem becomes ready for use; one of ``busy'', ``down'', and ``ready''.
The default state to use is ready.
FILES
Consult hylafax-server(5) for a complete discussion of the structure and content of the spooling area.
SEE ALSO
hylafax-server(5), faxgetty(8)
July 17, 1995 FAXSTATE(8)