02-23-2012
Something must have changed. Issues are just the results of one or more causes
Well, for starters, can you delete the private key and generate new public/private key and check? (to be honest if there was key mismatch, it would prompt you for password; should not hang)
Also, check if DNS is enabled in the remote machines's ssh config. If so, is you DNS server responding to the queries properly?
Does it happen while connecting from a particular server?
10 More Discussions You Might Find Interesting
1. Solaris
I am currently setting up rdiff-backup to use ssh to connect and remotely backup and retrieve data. I am doing so by creating rsa keys for each server and copying the relevant key to the /.ssh folder on the relevant server.
All seems to work well when severs running solaris 8 with ssh 3.6.1 are... (6 Replies)
Discussion started by: falklandtim
6 Replies
2. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
3. UNIX for Dummies Questions & Answers
Greetings!
I just managed to install Solaris 10 on a Sparc based machine. However, there might be a problem with the way ssh is configured.
I CAN ssh from the machine into another on the network (same subnet, as root), but then the newly installed machine CANNOT seem to accept incoming ssh... (2 Replies)
Discussion started by: agummad
2 Replies
4. Shell Programming and Scripting
Hi!
I have two solaris 10 machines(say 10.1.1.1,10.1.1.2). i have installed rsync on 10.1.1.2,
10.1.1.1:::
Sun Microsystems Inc. SunOS 5.10 Generic January 2005
-bash-3.00$ ssh 10.1.1.2 "echo $PATH"
Password:... (4 Replies)
Discussion started by: dddkiran
4 Replies
5. Solaris
Hi,
I am unable to login into my terminal hosting Solaris 10 and get the below error message
"Server refused to allocate pty
ld.so.1: sh: fatal: libc.so.1: open failed: No such file or directory "
Is there anyways i can get into my machine and what kind of changes are required to be... (7 Replies)
Discussion started by: sankasu
7 Replies
6. Solaris
Solaris 10 (Sun V210) System hangs every couple of months. Have to go into ALOM to reset. I did a consolehistory report and seen this in it.
Failed to exec inetd_start method of instance svc:/network/bootps/udp:default: I/O error
WARNING: /pci@1c,600000/scsi@2 (glm0):
Resetting... (3 Replies)
Discussion started by: Joeentech
3 Replies
7. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
8. Solaris
Anyone ever see an issue where ufsdump 'hangs' after the IV Pass?
Normally, it will update with an estimate of how long it will take to complete...and update the info every 20 minutes.
I'm running the following command:
root# ufsdump 0f - /fsmount | ( cd /zfs/newfsmount ) ; ufsrestore rf - )... (2 Replies)
Discussion started by: RTM
2 Replies
9. Solaris
I have a server with 6 Ethernet ports. 4 are the the motherboard based 1 GBE ports and 2 are 10 GBE ports on NICs.
I have set these all up with static IP addresses and use the standard /etc/nsswitch.files. My IP addresses are
net0 192.168.1.82
net1 192.168.2.82
and so on till
net5... (4 Replies)
Discussion started by: ashlaw
4 Replies
10. Solaris
Hi,
We just built a new Solaris 10 zone. And would like to add it to our DNS server. Its also Solaris 10. Please let me know how can I get the IP resolved using this DNS server. I added entry into zone config file but not working. I did restarted the DNS services. And also added nameserver name... (5 Replies)
Discussion started by: snchaudhari2
5 Replies
LEARN ABOUT DEBIAN
dropbearkey
dropbearkey(8) System Manager's Manual dropbearkey(8)
NAME
dropbearkey - create private keys for the use with dropbear(8)
SYNOPSIS
dropbearkey -t type -f file [-s bits] [-y]
DESCRIPTION
dropbearkey generates a RSA or DSS format SSH private key, and saves it to a file for the use with the dropbear(8) SSH 2 server. Note that
some SSH implementations use the term "DSA" rather than "DSS", they mean the same thing.
OPTIONS
-t type
Type of key to generate. Must be one of rsa or dss.
-f file
Write the secret key to the file file.
-s bits
Set the key size to bits bits, should be multiple of 8 (optional).
-y Just print the publickey and fingerprint for the private key in file.
EXAMPLE
generate a host-key:
# dropbearkey -t rsa -f /etc/dropbear/dropbear_rsa_host_key
extract a public key suitable for authorized_keys from private key:
# dropbearkey -y -f id_rsa | grep "^ssh-rsa " >> authorized_keys
AUTHOR
Matt Johnston (matt@ucc.asn.au).
Gerrit Pape (pape@smarden.org) wrote this manual page.
SEE ALSO
dropbear(8), dbclient(1)
http://matt.ucc.asn.au/dropbear/dropbear.html
dropbearkey(8)